TGS325GW0 Estate Range - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I removed the two screws that held the igntr in place. Then I pulled the igntr out and unplugged the wires. Replaced the igntr with the two screws and plugged the wires back together. I then turned the oven on to 400 degrees and it heated like a new one.

I removed the handle by unscrewing two philips screws located on the each side on the top inside of the door. I then placed the glass bottom end in first, lined it up on both ends, put the handle back in place and put the screws back.

Un-screwed 4 screws. Got part numbers off of the pieces. Put numbers in blank on web site and ordered the pieces. Parts cam in 4 days later and installed the pieces with my trusty screwdriver.

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

After I found the web site I looked at the possible solutions for my problem. My igniter was glowing so I was not sure that would fix the problem but several places indicated the igniter would fix the problem and after I replaced it the oven work great.

It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.

Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.

The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.

I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 minutes) after that.

Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!

I didn't. Don't know how to get to light bulb to change it for this specific model

Unplugged, took off back, removed old part, put on new part and connected. Replugged and it worked great.

I didn't do it, but I suggest putting down newspaper to keep from having to clean up all the charred remains that will inevitably fall from the parts you have to remove. First, unplug the thing so you don't shock yourself. I removed all the racks for easy access to the drip pan, which had to be removed by unscrewing two screws. Then there was a cover over the flame area that also required two screws being removed. The coil had two screws connecting it, but first I had to pull out the drawer at the bottom, crawl under the unit and unplug the coil. I removed the two screws from the old coil and replaced it with the new one, but first I had to get back under and plug in the new coil. I was unprepared for the virtual small animals that were under the stove, so I took some time to clean out that mess. I tested the thing to make sure it would work, and it did. I put all the pieces back in reverse order and had some really good baked chicken for dinner. I also recommend using gloves, as all the soot is hell on your nice manicure.

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.