TGS325GW1 Estate Range - Instructions

I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.

First I removed the oven racks. Then I loosened the two screws in the back of the oven floor and figured out how to remove it. Then I loosened the two screws at the front of the diverter and, with some pushing and pulling and twisting, was able to get that to come out, too. Then I tried lighting the oven and noticed that the igniter was not glowing. When I saw that the upper (broiler) burner was working fine, I hoped that the problem was the lower igniter itself. I checked the wires and they seemed fine. I saw that two bolts held the igniter onto its bracket, so with a socket wrench (which size I got right on the first guess!) I removed those bolts and the igniter came loose. I found the connecter for the wires when I removed the drawer under the oven and was able to pull it apart easily. The igniter came out completely. There was nothing unusual about it, but I decided to take a chance and order a new one, hoping that replacing it would solve the problem. I put the rest of the oven together and waited. About three days later the part arrived (it was sent on a holiday; FedEx is soooo much better than USPS). I retraced the steps of taking the oven apart, put the two bolts into the new igniter to attach it to the bracket, and went back underneath behind the drawer to connect the wires. Then came the moment of truth: I tried turing on the oven. I held the button down to keep the light off, and after a few seconds I saw it: IT GLOWED!! It worked!! After yelling a satisfying "YEAH!!," I turned it off, put back the drawer, the diverter (more pulling and pushing and twisting), and the oven floor. Now it's all working perfectly and it took a very short time to fix. And a little luck that the problem was with such a simple part.

I pulled the range from the wall and disconnected the power cord. I removed the grates, burner caps and the burners from the cooktop. Using a plastic putty knife, on either side of the range in the front I pushed the retaining clips to allow the cooktop to be raised. I used a short board to keep the cooktop open. I cut the wire leading to the broken igniter and removed the old igniter. I put the new ignitor in the mounting hole. The igniter wire connects to the spark module which is in the back of the range. To access the module I removed three top screws on the backplate(you have to get behind the range) and removed the top access panel. I used the old wire to pull the new wire through to the module. I disconnected the old wire from the module and connected the new one.

Reassembly was easy. I replaced the backplate and screws, lowered the cooktop, replaced the burners, caps and grates. I plugged the power cord back in and slid the range back.

Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cover

Broken ignitor wire had been previously removed to determine part number. Exact length was not availible (37"), but similiar unit (36") (one inch shorter) worked with zero problems. To re-install replacement wire/ignitor, I removed all four grates, and surface burners (allows top surface to pivot upwards.) Raised front of stove top surface by pushing in side, hold-down clips, using butter knife. Propped up surface with board. Insert clip end of igniter lead through hole in top surface and led wire back and towards passage to rear plug-in terminal location. Removed upper, rear sheet metal cover plate (must pull entire range away from wall.) Fed thin/ some-what-stiff safety wire down through plastic protection sleeve (all four ignitor wires go through the sleeve.) Wrapped wire around clip on end of igniter lead, pulled igniter wire up through plastic protector sleeve, disconnected pull through wire, and pushed connector clip on ignitor wire into ignitor terminal block. The rest was nothing more than screwing things back together in reverse order.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

screwed in the new glide by taking out old broken one and screwing in new one. wife happy now.

Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

Part came super fast, remove and replace two screws - nothing to it

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Removed racks and floor in oven, exposing ignitor assembly. Disconnected 2 wires at electrical connector plug. Removed 2 screws holding ignitor in place, removed bad ignitor, installed new ignitor in reverse order. Tested for ignition, all worked fine.

removed broiler pan
removed oven bottom plate
removed burner cover
unplug and remove igniter
reinstall igniter
clean and reassemble

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Found that the two screws securing the bottom had rusted away allowing me to just lift the old bottom out. The new one fit in place exactly and really did not need the screws. Done in 2 minutes.