TES355KT0 Estate Range - Instructions

1st; I opened the door, 2nd; removed the keepers that prevent the door from coming unhinged. 3rd; placed 2 short screws in the holes in the hinges. 4th; raised the door until it stopped. 5th; lifted the door upward and slid the hinges out of the slots in the range. 6th; laid the door face up on a microwave stand. With a handle on the outside, and hinges sticking out of the inside, it was inpossible to lay the door flat on a larger surface, and get around it. 7th; removed 2 screws from the inside top, and the 8 screws from the very bottom. 8th; removed the bottom rail, and the handle assembly. From there everything was stacked pieces. Picked the glass front up, and carefully set it safely aside. Picked each piece up and cleaned it, and started the re-assembly. The hardest part of the process was getting the fiberglass rope around the inside glass, to stay in place during the initial re-assembly. From there, the assembly was just the reverse order. the process was about 1 hour and 20 minutes, due to lack instructions and practice, plus cleaning, finding screws, and tools, Instructions may have been on line, but I didn't find them. The new hinges came with pins in place, and should have come with an extra set to lock the old hinges.

Removed the screws that hold the handle to the oven door. In less than 5 min had the glass in place and you couldn't even tell that I had broken the glass door.
super easy to change very helpful company to get stuff from.

Moved the stove out from the wall. Took out the screws from the back and then from the top. I pulled the piece through the back to unplug the clips from the elements. But the wires went back through the openings. So I had to take the back off of the stove to get to the wires to put back through the holes in the stove. Once the clips were back together, I put the back back on the stove. Rebolted the part to the stove and moved it back.

Very easy . Just removed four screws and removed the back cover. Then just unplugged two clips from the element . The repeated all of my steps in reverse . Be sure to unplug the oven before you start on the project .

Since it fell out, we didn't know how to put it back in--after several hours of frustration, thinking the glass was too big--we went to appliance store and looked at a stove and found out the glass went on the outside with only a groove and handle holding it in place. After that, it took about 30 minutes to complete.

Removed the trim by unscrewing 5 screws being careful not to drop glass panel. Had to scrape and paint over rust stains on the glass panel. After paint dried reinstalled with new trim (remodeled part only required 3 screws). Just a little tricky getting screws started while holding up the glass panel.

I removed the two screws that held the element in place . I think pulled out the element and disconnected the two wires. I put the new element in and connected the two wires. I went to put the element back in and something sparked and burned up the wire. Lesson learned - turn the electricity off first. I had to pay a repair man to come out and replace the wire.

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

The repair was easy. I had to remove the trim on the other side and the bottom. You slide the new trim on and screw in the bottom two screws.

Unplugged the range.
Removed the screws holding the flat top from the front bottom (inside doorway)
Unplugged the two connects at the back and removed the ground screw.
Unscrewed the bar holding the elements and remove the element.
Replaced with new element. Installation is reverse of removal.
Very easy if you are careful..Always unplug your appliance before working on it.

I removed the bottom srtip. Installed the new bottom strip, snapped in the side pieces. [The old ones screwed in.] Replaced the original handle. Ready to reinstall door.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element

I simply put the control knobs on the shaft and
they worked great. I love them. Thank you.