ESF34002W Range - Instructions

removed 2 philips screws holding element, un plugged element. new element arrive next day, insalled in less then 1 min. turned on, setoven for 375 pizza in 20 min later

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

ordered new broiler pan

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

I took the old wires and plug off and replaced it with the new block it works fine

Removed burner and then burner pan.Then replaced pan and reinstalled burner.

Had to use wd-40 to get the old part loose (oven is over 15 years old) and used pliers to pull apart from the oven. Replaced with the new part and works great. . . Once I used the wd-40 to loosen, it was super easy.

Unscrewed the 2 screws in the back of the element. Disconnected the unit from the bake of the oven, replaced the two ends of the new element and screwed in the 2 screws. Oven works great! Took less than 5 minutes to complete.
Thank you for the FAST delivery!!

This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.

I read up about the repair on the internet and what it entailed, thought I could do it. So followed directions from the internet after looking up Ammana, model number and serial number, and ordered the part from Part Select.com. It arrived two days later, was really impressed with their business handling of it.
I paid particular attention to disconnecting the power and pulling the plug out of the wall as double insurance to not getting electrocuted.
The Installation was quite simple, just pull the old one out and put the new one in. I took note of how the old one came out, and connected the new one in the same fashion, and it works wonderfully, just heated right up. It was a good experience.

Bought a new one. . Three years later =)

Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts together with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.

took out old element, replaced with new.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.