EI30GS55LBA Electrolux Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Smyrna, DE
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
glo plug wouldn/t ignite
took out the old (2 screws) put clip on wires and put the new part in. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from broadview heights, OH
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven would not ignight
followed posted repair procedure on Parts select site. . . straight forward and simple. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Fresno, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven not heating and theres a smell of gas.
1. Unplugged unit and shut gas off.
2. Removed the oven door(2screws).
3. Removed the oven floor(3screws).
4. Removed heat dispersion plate(1bolt).
5. Removed faulty igniter(2screws).
6. Labeled and spliced wires.
7. Connected new igniter.
8. Installed all previously removed parts.
9. Restored power and gas to unit and oven
fired up in a matter of seconds.....Thanks
2. Removed the oven door(2screws).
3. Removed the oven floor(3screws).
4. Removed heat dispersion plate(1bolt).
5. Removed faulty igniter(2screws).
6. Labeled and spliced wires.
7. Connected new igniter.
8. Installed all previously removed parts.
9. Restored power and gas to unit and oven
fired up in a matter of seconds.....Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Scotia, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven would not light
suspected oven ignitor,went to partselect website and saw
others had same concern and ignitor was the failed part.ignitor was not getting white hot just orange-not enough
voltage going to the gas valve to open it.ordered and replaced
ignitor.repair took about 20 minuets-oven repaired.
others had same concern and ignitor was the failed part.ignitor was not getting white hot just orange-not enough
voltage going to the gas valve to open it.ordered and replaced
ignitor.repair took about 20 minuets-oven repaired.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Forest City, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Would turn oven on, gas smell and would not light .
After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLY from DUCKHILL, MS
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven was slow on lite up
removed bottom plate in oven removed three screws and cut two wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from Washington, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not light
took off bottom pan in oven and replaced ignitor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merle from Monticello, IN
- Parts Used:
- 5303935066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven taking long time to start and shutting down while baking
The oven igniter was working, the Sears repairman said by the phone the igniter was probley weak and not geting hot enough. Remove door ( 4 screws) Remove oven pan (4 Screws) remove burner sheld. remove lighter and cut wires. Install new. Remove storage drawer and splice new wires to the old at the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter from bronx, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not heat up smell of gas
i followed some of the tips provided, and added a few of my own. unplug stove from electric outlet. open oven door, remove wire trays. remove the two flathead screws, holding down the oven pan, it should slide out easily. remove oven burner(looks like wings)only one nut holding it in place with 1/4"nutdriver. remove igniter, 2 nuts as well with 1/4" nutdriver. cut wires, leave a good length, and strip(2 wires). install new igniter, strip the 2 wires as well, trim to size, and with the two wire caps provided, make wire connections. tuck any excess length of wires away from igniter. re-install all parts the were orginally removed. plug oven back into outlet. turn on oven, and presto, oven worked good as new. saved a couple of hundred dollars doing the repair myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAULA from AUSTIN, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Top part of stove worked but not the oven
I googled most of the problem I was having. When I would turn on the oven I would have the orange glow from the igniter but I would never get heat. I ordered the part off this website...it arrived the very next day!!! 7 months pregnant I fixed the problem!!! My oven works beautifuly!! Just in time for the holidays! I saved so so much money doing it myself. U to can do it, good luck!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Circleville, OH
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The oven igniter would glow but the oven wouldn`t lite
After finding your page and using your trouble shooting guide, it was easy getting the right part and the video helped a lot. Removed the over rack- removed two screws to remove the bottom- two screws to remove the burner. Clipped the two wires to the old igniter and removed the burner from the oven,removed the two screws holding the igniter and installed new one. clipped the wires to length and renistalled the burner. Using the two wire nuts supplied put the wires togather and reinstalled the bottom. Everything went well lite first try with no poof sound. Just in time for Thanksgiving cooking. Got fast delivery of parts. Will uas again. Thanks Partselect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Warminster, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Bake unit did not ignite
Followed service sheet. Measured 2.6 amps draw at igniter wire which should have been 3.2 amps. Replaced igniter and problem resolved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brett from newbury pk, CA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
wouldn't light.
First, I read all the instrutions that came with my replacement part from Parts Select thoroughly (twice) then follewed them like an experienced surgeon. I removed the lower drawr after turning off the gas and unplugging the stove and then took out the bottom panels inside the oven to expose the screws holding the ignitor coil. Removed it, then cnnected the new one to the existing wires as they were in the stove and the drawing in the instructions, then replaced everything in the reverse of them coming apart. Plugged it back in, turned the gas back on and now it,ll bake things again. YEAH!! Parts Select!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Oceanside, CA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not light..
cut wires and removed the burner . Removed the ignighter and installed the new with nut driver. slipped the burner back in place and nutted the wires...Wallagh!!! fired right up...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derrick from Houston, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
oven would not ignite
after reading other replies i was 100 percent sure that my igniter was the problem . just as others said it had a veryh dem glow . once i changed it the oven lit in about 5 seconds .very easy to install and saved at lease $ 400 on not needing a new stove. thanks parts select . com
Was this instruction helpful to you?
Thank you for voting!