EW30EF65GSH Electrolux Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Darrell from Freeland, WA
- Parts Used:
- 316443920
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
oven would continue to heat after set temperature was reach/indicated on the display panel.
First had to determine what was the source of the problem. Removed the back panel to expose the heating element connections. Cycled thru the different oven settings; bake, convection bake, roast. convection roast and broil, while checking the voltage on the 3 heating elements; upper, convection and lower elements. As the oven cycled thru the different temperature settings the volt meter showed that the lower element would not shut down when set temperature was met. Checking the wiring diagram showed that the culprit was probably that the lower element relay in the relay panel was not cycling as required. Decided that replacing the relay panel would fix the problem, and it did. Replacement of the relay panel was very easy and the PartsSelect part was the exact part required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eloisa from SPOKANE VLY, WA
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Range not heating properly
The youtube video clearly described how to remove the back panel and how to replace the probe.
The repair took maybe 20 minutes to complete and 1/2 of that time was spent cleaning behind and underneath the range!
Range is working perfectly now!
The repair took maybe 20 minutes to complete and 1/2 of that time was spent cleaning behind and underneath the range!
Range is working perfectly now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melinda from Three Rivers, MA
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Rusted leveling foot
I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Greentown, PA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven temp was not right
We removed the old part and replaced it then when warming the oven all of a sudden there was a loud noise and something went and so we called a repair man which I guess we should of done in the first place. Now he has ordered a part that cost 170 soo that is my story don't try to repair if you don't have experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from MORGANTOWN, WV
- Parts Used:
- 318178110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
2 elements stopped working.
My husband followed the video instructions and it was easy to fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHAUN from ALBUQUERQUE, NM
- Parts Used:
- 316490000
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
slow to get to temperature
first the temperature sensor then the igniter. started to do the igniter by using common sense then I used YouTube which made it a lot faster.
the temperature sensor installs from the back of the stove, the igniter installs from thr front ie, the drawer and inside oven.
the temperature sensor installs from the back of the stove, the igniter installs from thr front ie, the drawer and inside oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- German from SELLERSBURG, IN
- Parts Used:
- 5304533520
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Center of dual burner was broken
Removed screws on the sides and front.
Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse.
Labeled the wire sets connected to the front control panel.
Gently lifted up the stove top and flipped it over on to a towel.
Removed the piece of metal holding down the burner.
Disconnected the cables to the old burner.
Repeated steps above in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from GILROY, CA
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven was not heating up properly
I followed the video on the website. The probe is on back of the oven. Just unplug part and replace. That was not our fix all though as I later found that the igniter was not working. The igniter is also an easy fix but you access it through the front of the oven. Also an easy swap.
Oven is working great now.
Our issues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.
If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.
Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.
Thanks
Oven is working great now.
Our issues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.
If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.
Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.
Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from S CHESTERFLD, VA
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven was over heating. In bake mode broiler would glow red and didn’t cut off after preheat
Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from CARVER, MA
- Parts Used:
- 316496205
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Roll out rack didn't roll
Went online to find replacement rack. Didn't want to spend the money for a rack I didn't like. Besides the range is 11 years old. Still in great shape. Opted for the simple oven rack.
Open the box and place in oven. Wah lah..
Thank you partselect.com
Open the box and place in oven. Wah lah..
Thank you partselect.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felicia from FORT MILL, SC
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven wasn’t heating
Used instruction video & replaced part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from CLIFTON, NJ
- Parts Used:
- 316490000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven temp was not heating up to desired temp and using an oven thermometer to confirm
moved the range out to access back
removed 5 screws from back panel
removed 1 screw from thermostat installed new one
replaced screws, done in 20 minutes
problem solved
removed 5 screws from back panel
removed 1 screw from thermostat installed new one
replaced screws, done in 20 minutes
problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from SIERRA VISTA, AZ
- Parts Used:
- 316442120
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Right front burner would not turn off.
Lifted stove top to disconnect burner wires in order to use stove until parts arrived. Remove a bunch of square drive screws to remove back panel from stove. Identify relay board and disconnect wire connectors from it then release several plastic clips and two screws holding board to oven. Install new board and connect wires, No other adjustments were required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PORT ORANGE, FL
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove was dropped and had broken, bent frame and adjuster feet
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from BRISTOL, IN
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
F10 code going off
Went well, and working thank you ??
Was this instruction helpful to you?
Thank you for voting!