EI30GS55JSC Electrolux Range - Instructions

Remove two screws in back to release the top.
Lift the top from the back and pull backwards to remove.
Open washer door and unscrew two screws to release the switch.
Reach down inside from the front and remove the switch.
Unplug the switch and replace with the new one. Reverse the process to install.
I found it easier to have someone hold the switch while I screwed it back in.

Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.

After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!

removed bottom plate in oven removed three screws and cut two wires.

Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.

It was a snap!

I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.

In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.

The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.

I removed the oven bottom which was held by two large head long screws. I then removed the heat deflector using a small socket. The only difficult part was when I went to replace the igniter. The screws that were holding it in place stripped I guess do to the amount of heat they were continually subject too. I had to apply pressure to the igniter bracket while removing the screw using a small socket. Even with that they did not come out easily. If I had not had trouble removing the screws the repair probably would have taken 15 min.

followed the instructions that come with the part. very quick and easy.

Removed lower burner covers and fan cover to access igniter. Unscrewed igniter and pulled out as far as possible. Marked both wires and snipped them. Twisted on wires from new igniter and mounted igniter. Pulled excess wire thru to back of oven and reassembled covers from first step. Last step was to explain to wife that she needs clean in there MUCH better.

pulled stove out to unplug the electric cord. Took oven door off and removed the bottom panel (2 screws) and then removed the burner (2 screws). took off old igniter ( 2 nut screws). cut wires and stripped the coating to wire to new unit.
Attached new igniter to the burner, and put the burner back in place and replaced the screws so unit was stable.
Turned oven on to make sure ingiter was going to light oven, when oven came on, turned oven off and replaced the cover to the burner and the bottom panel in the oven,. Put the oven door back on........
Probably took 45 minutes.
I ordered the part late Friday afternoon, around 3, and the part was here Saturday Afternoon. I was impressed.

took drawer out, removed tin covers, found igniter and removed,snipped off parts to put on new igniter ,wirenutted old to new put back together ,we had ignition! all in all pretty easy job! detailed instructions that came with new part were easy to follow and precice

Remove the oven drip pan & burner baffle. unscrew & cut leads to remove old igniter. Splice old leads to new using furnished wire nuts and remount. Job would have been easier with oven door removed, but didnt want to create a new project.

1. Unplugged power cord.
2. Removed warming drawer and oven shelves and lower plate
3. Removed old wirenuts from back of warming draw space (awkward to reach in to the back).
4. Removed 2 screws holding ignitor in oven - screws in poor shape and were not reuseable.
5. Found next size up sheetmetal screws and installed new ignitor.
6. Ran wires down adjacent to gas feed into warming drawer space.
7. Connected with wirenuts supplied with ignitor.
8. Replaced everything.
9. Tested oven and ate some tasty blueberry muffins.

I exposed the ignitor through the inside of the oven and then removed the two screws that held it in place. I then cut the wires underneath the stove ans reconnected them to the new part with the wire nuts provided. It was a simple repair.

Unplug appliance. Remove the bottom of the oven (2 screws in back of oven bottom), remove burner cover (2 screws in front and nut in center holding burner). Pull out the bottom storage drawer under the oven and unplug both wires from oven Igniter which are located in the back. One wire plugs into the gas valve and the second wire went into a connector that was on the lower left. I removed the screw on the back oven wall that held the burner so I could remove the burner for ease of work. Remove two screws holding the old igniter. The two screws holding the igniter to the side of the burner were stripped and they took a little time to remove but I replaced them with two new screws I had in my misc. screw drawer and had no issue. Cut the top wire and splice it onto the top wire of the new igniter using the porcelain wire nuts provided. Do the same with the bottom wire. Re-assemble and plug back in. Everything worked perfectly.