EI30GS55JSA Electrolux Range - Instructions

followed online instructions

I simply searched YouTube for the problem I was having and foud it was probably caused by a bad part. I found the part online and ordered it. It was as simple as a few screws and a couple wire-nuts to install. My girlfrind was very happy to get the oven fixed !!!!
Thanks parts-select for having pictures and dimensions so I was sure I had ordered the exact right part.
I was soooo happy to have found you !

pulled stove out to unplug the electric cord. Took oven door off and removed the bottom panel (2 screws) and then removed the burner (2 screws). took off old igniter ( 2 nut screws). cut wires and stripped the coating to wire to new unit.
Attached new igniter to the burner, and put the burner back in place and replaced the screws so unit was stable.
Turned oven on to make sure ingiter was going to light oven, when oven came on, turned oven off and replaced the cover to the burner and the bottom panel in the oven,. Put the oven door back on........
Probably took 45 minutes.
I ordered the part late Friday afternoon, around 3, and the part was here Saturday Afternoon. I was impressed.

Let me begin to say your service was great. I received the unit the next day. Also your price was good.
The whole job took me an hour. I would have done it sooner but I didnt a square head driver bit to remove the igniter from the burner assembly. I removed the whole assembly and with a pliers slowly unscrewed the mounting screws. After that I disconnected the igniter per your instructions,spliced the remaining wires reconnected the gas and electric and I was good to go.

I removed the oven bottom which was held by two large head long screws. I then removed the heat deflector using a small socket. The only difficult part was when I went to replace the igniter. The screws that were holding it in place stripped I guess do to the amount of heat they were continually subject too. I had to apply pressure to the igniter bracket while removing the screw using a small socket. Even with that they did not come out easily. If I had not had trouble removing the screws the repair probably would have taken 15 min.

followed the instructions that come with the part. very quick and easy.

Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.

A friend replaced the new ignitor with the old one...very simple job.

I would like to comment on how fast the service was from when I ordered the part online to 3 business days later when the part arrived....very happy about how easy it was to order part and that the part was in stock and delivered so quickly. Thank you very much !! I will recommend Part Select to a friend that frequently orders parts.

1. Unplugged unit and shut gas off.
2. Removed the oven door(2screws).
3. Removed the oven floor(3screws).
4. Removed heat dispersion plate(1bolt).
5. Removed faulty igniter(2screws).
6. Labeled and spliced wires.
7. Connected new igniter.
8. Installed all previously removed parts.
9. Restored power and gas to unit and oven
fired up in a matter of seconds.....Thanks

suspected oven ignitor,went to partselect website and saw
others had same concern and ignitor was the failed part.ignitor was not getting white hot just orange-not enough
voltage going to the gas valve to open it.ordered and replaced
ignitor.repair took about 20 minuets-oven repaired.

Figured out which part we needed by reading about others problems; Followed instructions & Presto = oven heats!!!! Didn't have any problems removing or replacing part.

The oven igniter was working, the Sears repairman said by the phone the igniter was probley weak and not geting hot enough. Remove door ( 4 screws) Remove oven pan (4 Screws) remove burner sheld. remove lighter and cut wires. Install new. Remove storage drawer and splice new wires to the old at the back.

i followed some of the tips provided, and added a few of my own. unplug stove from electric outlet. open oven door, remove wire trays. remove the two flathead screws, holding down the oven pan, it should slide out easily. remove oven burner(looks like wings)only one nut holding it in place with 1/4"nutdriver. remove igniter, 2 nuts as well with 1/4" nutdriver. cut wires, leave a good length, and strip(2 wires). install new igniter, strip the 2 wires as well, trim to size, and with the two wire caps provided, make wire connections. tuck any excess length of wires away from igniter. re-install all parts the were orginally removed. plug oven back into outlet. turn on oven, and presto, oven worked good as new. saved a couple of hundred dollars doing the repair myself

I googled most of the problem I was having. When I would turn on the oven I would have the orange glow from the igniter but I would never get heat. I ordered the part off this website...it arrived the very next day!!! 7 months pregnant I fixed the problem!!! My oven works beautifuly!! Just in time for the holidays! I saved so so much money doing it myself. U to can do it, good luck!!

after reading other replies i was 100 percent sure that my igniter was the problem . just as others said it had a veryh dem glow . once i changed it the oven lit in about 5 seconds .very easy to install and saved at lease $ 400 on not needing a new stove. thanks parts select . com