CE35111AAT Crosley Range - Instructions

It was easy finding the part on line and the part was delivered within three days. It only took about 10 minutes to change element. I was so pleased with the product, that I just changed a thermostat on my parents stove which was purchased through parts select and that was very easy to change also.

Unscrewed two Phillips screws holding the element in the back of the oven, pulled out the element and the leads, disconnected the wires, removed element from oven and reversed the process to install new one. One most important and critical maneuver - the element is connected to the hot wire on the left side and the switch shuts off the element by disconnecting electrical flow to the neutral side of the power so its not enough to just have the oven turned off - makes one heck of a spark when the wire touches the stove panel when you pull the wire through the hole (220 at 60 amps).

Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.

Turned off power to oven. Removed screws from each side of element. Removed connectors to disconnect old element. Connected new element to connectors. Replaced screws, then turned on power to oven. Turned on oven to heat. Easy install.

Video showed element being unplugged from inside oven. My oven wires did not extend into oven cavity and they fell behind the back oven wall when I unplugged them. After trying to catch the two wires using needle nose pliers through 3/4" holes several times, I finally decided to take the complete back off the range. When I did this, I was able to see the wires with the female couplings. I then had my wife firmly hold the new element against the back of the oven from inside letting me connect the wires to the new element and replace the oven back. THIS WOULD HAVE QUALIFIED AS "EASY" AND A 15 TO 30 MINUTE JOB if this technique had been known from the outset.

I checked out Maytag.com - found the parts page on my computer - found the top oven element - ordered it from Part Select - it arrived just a few days later......

Before it arrived, I removed the damaged electric element from top of oven - easy.

Oven was ready for me to install new element - the video on your website was perfect - it helped me remove the old & install the new element from Part Select. It took me about an hour.

Thank you for your fast service, good instructions & the video!

I'm an 84 year old female. Did this by myself! Thank you!

We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.

Looked at parts blow-up, watched a You-Tube video,

Had to remove 4 small rusty screws and a sort of guard made of metal. With power off, I had no light to see way in the back of the oven. Suggest use of a head-lamp.
Also, it would have been very helpful if when the part arrived, it was noted somewhere that a smell and “smoking” from the part is very normal. This would have saved me a tremendous amount of stress and more days without the broiler trying to figure out if I did something wrong, if the part was bad or other. Sounds so simple, but BOY, that would have been SO helpful

used the supplied parts...very easy. The parts were exact replacements.

I've been trying to remove the bracket at the roof of upper oven so I can get to the broiler element itself. The screws are in place so tight, the won't move. I've used regular as well as ratchet screwdrivers and the screws still won't move. I don't want to spray WD 40 in oven because of a possible fire hazard, so I haven't changed out element yet. Tried calling customer service for advise, but to no avail. All other screws loosen easily. What should I do next.

1) Unplugged the electrical cord and removed the oven door (only when easy); and, jockeyed the oven into better working area.
2) Removed about 9 screws holding rear sheetmetal backing plate to disconnect each of 2 electrical wires from the old element.
3) Removed 2 screws holding element to back of oven and 2 screws from small bracket supporting end of element to top of oven.
4) Replacement element was severely damaged. It was at the very bottom of a box 20 by 15 by 15.5 inches high with the large continuous bubble wrap stacked only on top. Each of the wire ends were sharply bent; one almost 180 deg. pointing in the opposite direction, and the other about 120 deg. The element itself was about 4-5 inches out of square. Using two large needlenose pliers I carefully bent each wire back to its proper place. Next I carefully exerted pressure on the element to gradually form it back to as near its correct shape as possible. (Only the inside of the shipping box showed the signs of possible damage.)
5) Installation- The element, from inside the oven, was placed back through the two holes in the rear of the oven and secured with 2 screws.
6) The bracket supporting the front of the element was slid onto the element and attached to the top of the oven.
7) Attached the 2 electrical oven wires to the 2 element wires, making sure there was good clearance to prevent any short circuit, plugged the oven cord in to 230volts, and checked it out with power to the broiler to give myself some confidence that the damaged wires would not quickly break. It seemed to work and I unplugged the oven.
8) Reinstalled the backing plate with the original screws, plugged oven back in, and moved the oven back to its place and replaced its door. It is working and my wife is cooking.

First off, I ordered the part to be delivered 2-3 business days. I ordered this online on Sunday, so I figured it wouldn't show up until at the earliest on Thursday. We got it on Tuesday. Fantastic. Once I got it I pulled the range out and unplugged it. Next I removed the two screws holding the old element in place with a phillips screw driver. Pulling the old element out carefully I removed the two wires from either end. Next I attached the wired to the new element and screwed in place. Fast and easy! Plugged the range back in and we were cooking.

1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

remove elements and replace bowles