CE35111AAD Crosley Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Green Lane, PA
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned-out.
Removed element's two mounting screws and disconnected the wire leads on each end. Connected wire leads to the new element and replaced mounting screws. Only took a few minutes to make the change. The oven is good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Houston, TX
- Parts Used:
- 7730P011-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Indicator Lens melted and fell back into the control panel
I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford A from Melbourne Beach, FL
- Parts Used:
- WPW10310249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broil element non functional
Power turned off. Door of the oven lifted off. Four screws removed, old element pulled out to reveal electrical connectors. Wires easily removed, and element discarded. New element connected to the two conductors, four screws installed and the job was completed.
Very easy. Took about 10 minutes.
Very easy. Took about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Big Arm, MT
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned out. Actually it broke in half.
When ordering the replacement part, read the posts on how to replace the bake element. Just follwed their lead. The only difficulty is getting a hold of the wire at the back of the range that the bake element plugs into. There wasen't much play in the wire.
PS Be sure and remove the range door or have very long arms.
PS Be sure and remove the range door or have very long arms.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Holly from Plainview, MN
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
broken element and wire
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Oldsmar, FL
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the control pannel shorted out (circuit board timer)
Moved the stove, unplugged it. took the back off, took out old board installed the new one. It was just that easy and saved us from buying a new stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Meridian, TX
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The original element broke when dad spilled a liquid on it while still hot.
Disconnected power to the range, Took off the oven door removed two screws and disconnected the two electrical connections to the heating element. Made the two connections to the new element and replace the two holding screws. Replace the oven door and plugged in the power cord. Turned on the oven to test and was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dinh from austin, TX
- Parts Used:
- 7403P238-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
one electric burner does not get hot
swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from San Luis Obispo, CA
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner control knob/switch shaft had broken off.
Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Reno, NV
- Parts Used:
- 74003387
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
old bulb fused into old socket.
removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex from Clyo, GA
- Parts Used:
- WP74005019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not shut off
Removed back top and lower covers, raised top of stove, opened oven door to remove probe and pulled probe out.Then I ran new probe back in just like it was removed.I took two screw out of the oven switch and removed the wire one at a time and mounted switch back with the two screws put knob back on. Job complete works like new again.Thanks Alex
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miguel R from MCKINNEY, TX
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element stopped heating
I unplugged the cord to the stove. Then I removed the two screws on the broken heating element. Once the screws were removed, I slid off the two wires attached to the element prones. Grab the new element and attached the two wires. Reinstalled screws. Plugged in the cord, and turned on oven. Heating element came on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from WINCHESTER, MA
- Parts Used:
- WP7212P043-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1960's oven door gasket fell apart, actual gasket not available any more
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from LAKESIDE, CA
- Parts Used:
- WP74010750
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element had deteriorated
Turned the power off to the oven, unscrewed the ends of the element, connected new element, screwed it back in to place and turned the powe back on. The video provided in my shipping confirmation was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MUNFORD, TN
- Parts Used:
- WP74005019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven stayed on in the off position.
Removed the 2 rear panels and removed the 2 screws holding switch in place; Removed the wires to the switch and replaced.
Was this instruction helpful to you?
Thank you for voting!