CGA2D2K-1 Crosley Range - Instructions

Replaced the oven ignitor. Toughest part was removing old screws.

Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!

open oven door remove bottom tray pull off two screws unplug wire remove old part install new part

I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".

Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Such a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."

well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow

I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.

Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!

Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the igniter came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.

Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.

My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of cake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!

The Just Answer website answer felt certain that the igniter was the problem, and hence I ordered a new igniter.
I removed the oven bottom plate and the cover over the valve connection to get an overview of the job. Was really not necessary. Actual repair was only to remove the two screws holding the igniter, pull the cord to get to the connector, and switch igniters. Then put everything back together again. Job done. Oven works great.

We replaced Flat Style Oven Igniter simply by removing the oven racks, then removed the bottom of the oven. Used a Philips screwdriver to remove the old igniter, placed new one in. The wires to the oven from the ingniter just needed to be in a clip. Tightened the screws and replaced bottom & racks. Oven worked wonderful after this, like a brand new oven!

unplugged the oven, unplugged the ignitor and removed the two screws

First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took about 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)