CE35100AAT Crosley Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eugene from San Antonio, TX
- Parts Used:
- 12001676
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Burner wouldn't heat (wiring failure)
1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Meridian, TX
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The original element broke when dad spilled a liquid on it while still hot.
Disconnected power to the range, Took off the oven door removed two screws and disconnected the two electrical connections to the heating element. Made the two connections to the new element and replace the two holding screws. Replace the oven door and plugged in the power cord. Turned on the oven to test and was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Irving, TX
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Georgiana, AL
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom oven element burned out.
This was very easy. All I did was unscrew the brackets from the back of the oven holding the element. Then I removed the wires from the bad element and reversed the procedure adding the new element. It was easy to order the right part and I got the item in plenty of time for the Thanksgiving holiday!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Green Lane, PA
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned-out.
Removed element's two mounting screws and disconnected the wire leads on each end. Connected wire leads to the new element and replaced mounting screws. Only took a few minutes to make the change. The oven is good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Holly from Plainview, MN
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
broken element and wire
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford A from Melbourne Beach, FL
- Parts Used:
- WPW10310249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broil element non functional
Power turned off. Door of the oven lifted off. Four screws removed, old element pulled out to reveal electrical connectors. Wires easily removed, and element discarded. New element connected to the two conductors, four screws installed and the job was completed.
Very easy. Took about 10 minutes.
Very easy. Took about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Houston, TX
- Parts Used:
- WP7730P011-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Indicator Lens melted and fell back into the control panel
I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dinh from austin, TX
- Parts Used:
- WP7403P238-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
one electric burner does not get hot
swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Big Arm, MT
- Parts Used:
- WP74010750
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned out. Actually it broke in half.
When ordering the replacement part, read the posts on how to replace the bake element. Just follwed their lead. The only difficulty is getting a hold of the wire at the back of the range that the bake element plugs into. There wasen't much play in the wire.
PS Be sure and remove the range door or have very long arms.
PS Be sure and remove the range door or have very long arms.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Oldsmar, FL
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the control pannel shorted out (circuit board timer)
Moved the stove, unplugged it. took the back off, took out old board installed the new one. It was just that easy and saved us from buying a new stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from San Luis Obispo, CA
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner control knob/switch shaft had broken off.
Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alex from Clyo, GA
- Parts Used:
- WP74005019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not shut off
Removed back top and lower covers, raised top of stove, opened oven door to remove probe and pulled probe out.Then I ran new probe back in just like it was removed.I took two screw out of the oven switch and removed the wire one at a time and mounted switch back with the two screws put knob back on. Job complete works like new again.Thanks Alex
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Biscoe, AR
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burnt out
It is very easy shut off the power yo the stove at the fuse box, unscrew the two screws and pull the element out replace and screw back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from SAINT PETERS, MO
- Parts Used:
- WP7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front 8" burner stuck on high no matter where dial was set.
This range was easy. Only 4 screws under the front panel that allows the panel to come off. No need to pull the range out for back screws.
Replacement part was exact and worked perfect.
Turn off the circuit breaker for the range.
Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.
Pull the bottom of the front panel out about 30 degrees and lift off the top.
Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.
Replacement part was exact and worked perfect.
Turn off the circuit breaker for the range.
Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.
Pull the bottom of the front panel out about 30 degrees and lift off the top.
Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.
Was this instruction helpful to you?
Thank you for voting!