CC3531XRL Crosley Range - Instructions

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.

I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)

1. Ensure oven is powered down and cool to the touch. For extra assurance, throw the circuit breaker to the range to OFF. 2. Pulling gently but with constant force remove the right rear surface burner element from its receptacle. 3. Remove right rear drip bowl. 4. Using a #2 Phillips screwdriver remove the single screw that holds the vent cover. 5. Lift the oven top, it should latch open. 6. Remove the vent cover - you may need to pry it very slightly with a slot screwdriver if it has never been removed, it tends to stick from accumulated cooking smudge. 7. Clean up the area where the new cover will go. 8. Install the new cover and screw it snugly, but don't overtighten. 9. Using releases on latching struts,lower oven top. (Cautiously, so as not to pinch your fingers as the top drops!) 10. Re-seat the drip bowl and carefully plug the heating element back in, making sure it seats properly in both the electric receptacle socket and how it sits on the stove top drip pan. Done! (Don't forget to switch the breaker back on, if you turned it off.) I explained this in great detail, but it shouldn't take more than 5 or 10 minutes to accomplish the whole task.

New receptacle element. I am a girl and I did it.!!!!

Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done

Our Maytag Gemini is about 10 years old. One night the 8" front right element was smoking and had a white hot spot on the burner. I quickly turned it off and after the element cooled I removed it. Since one 8" element was burned out, but the rest of the range and oven worked, I assumed I could get it fixed. Rather than call the service man for $99 for a diagnostic visit, I decided to go to PartSelect and get prices on parts. They had the easiest site to use with part numbers, exploded part drawings, etc. Since I had to replace one burned out element anyway, I ordered the burner and the wiring receptacle. I assumed that was step one. The parts came in about two days. It took me about 20 minutes to put them in with no problems. Very easy. However, the burmer still would not work. I went back to the site and determined the only other part it could be was the infinite switch. The bad element little light on the top control panel was not going out even after I put in new parts. I figured it was shorted out and frozen in the closed position, so I ordered a new one from PrtSelect. It came again in about two days. This part was easy to replace, except it took longer because the entire back of the oven had to be removed. Three pieces of sheet metal had to be removed and two plastic end caps. Sheet metal has sharp edges. Watch out that you do not get cut. A lot of screws got removed and put back. You have to be careful that the three pieces of sheet metal are put back correctly because several edge tabs lap over each other. The infinite switch fixed the problem. Took me about two hours to do the switch replacement, but that counted cleaning the sides of the oven and underneath the oven (Yuch!). Now everything works fine. I suspect that the old wiring receptacle was fine and just the infinite switch and element needed to be replaced. In any case, the wiring receptacle was cheap. In the end, the repair cost me the same $99, but I spent it in parts and not parts plus installation so I was way ahead.

So purchased two new 8 inch elements and replaced them.

finished removing door seal, used pliers to remove old securing studs. positioned new seal and pushed securing studs into existing holes and was done.

used drill to remove old screw

I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.

I have worked in maintenance field most of my adult life and all aspects and to change the oven door gasket was no challenge what so ever. It took longer to find my needle nose pliers to remove the old gasket clips and then re-install the new gasket. Maybe 10 minutes total