WFF334GCB Crosley Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dave from LOUDONVILLE, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven element burnt out.
Remove 2 screws. Pull element out. Slide 2 wires off. Just do in reverse it's done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from KEENE, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner not controlable
Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from LAUREL, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burned out
This is an easy repair, as described in several other replies. One important addition to what has already been described. Very important to turn off the breaker or unplug the range. One terminal of the range is connected to a hot wire and the range housing is grounded. You may not manage to electrocute yourself, but you could cause and arc that damages the housing or connector. Turn off the power. Beyond that, simple. Unscrew two 1/4" screws with a nut driver, slide the element out and disconnect the wire connectors. Reverse procedure to install the new element and turn the power back on. Preheat briefly to burn off any odor. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rosetta from COLUMBIA, VA
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
problem pulling out bottom tray on range
just put in slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from COFFEYVILLE, KS
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
broke
took out the old one, screwed in the new one. very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amber from CARLISLE, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element (bottom of oven) burnt through and snapped in two
Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Ellenville, NY
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Old heating element broke
Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated with another beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from RESTON, VA
- Parts Used:
- 389082702
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Replace the dual-element burner in glasstop range
The how-to video was helpful, though my old range has an extra spacer panel between the glass-top and oven, requiring an extra couple of screws to be removed, with different-sized Philips head.
1. Replacement part was not exactly like the original.
* Inner and outer elements lacked an insulating spacer.
* The two wiring terminals/docks were swapped.
* So had to attend to where the wires were going.
* Worked, just needed some observation & thought.
2. MOUNTING HOLES
a. Old element had clips mounted at holes 9 & 45.
b. Old element had the four-terminal wiring dock attached by screws at 71 & 72 (also where 0 would be), “ahead” of the small three-terminal port by about 5 number positions.
c. Corresponding holes in replacement were not the ones with pre-drilled insulating material. But it's really soft and easily drilled by hand. Probably could have just screwed directly into it.
d. Replacement four-terminal dock is “behind” the smaller one by a few number spots.
3. WIRING IS REVERSED
As noted, the two terminal docks are swapped, so watch the wiring.
Old terminal docks/ports were directly connected by a wire shunt that tied those terminals to the inner ring element.
The new element also has inner/outer burners, with no separation, but we can trace the wiring. Instead of a shunt, the docks are connected via the element. The right port on the small dock is connected to the inside burner, and that inside burner element exits into the large dock. That’s
the inside-burner circuit.
1. Replacement part was not exactly like the original.
* Inner and outer elements lacked an insulating spacer.
* The two wiring terminals/docks were swapped.
* So had to attend to where the wires were going.
* Worked, just needed some observation & thought.
2. MOUNTING HOLES
a. Old element had clips mounted at holes 9 & 45.
b. Old element had the four-terminal wiring dock attached by screws at 71 & 72 (also where 0 would be), “ahead” of the small three-terminal port by about 5 number positions.
c. Corresponding holes in replacement were not the ones with pre-drilled insulating material. But it's really soft and easily drilled by hand. Probably could have just screwed directly into it.
d. Replacement four-terminal dock is “behind” the smaller one by a few number spots.
3. WIRING IS REVERSED
As noted, the two terminal docks are swapped, so watch the wiring.
Old terminal docks/ports were directly connected by a wire shunt that tied those terminals to the inner ring element.
The new element also has inner/outer burners, with no separation, but we can trace the wiring. Instead of a shunt, the docks are connected via the element. The right port on the small dock is connected to the inside burner, and that inside burner element exits into the large dock. That’s
the inside-burner circuit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from FRUITHURST, AL
- Parts Used:
- 316436000
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Old part was replaced by mfg’r. Wiring different. No drawings or any info was included to show wiring.
I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Jacksboro, TN
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken drawer slide
Remove drawer. Insert new slide. Install drawer.
Was this instruction helpful to you?
Thank you for voting!
Broken right side parts for lower over storage drawer.
Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW HYDE PARK, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The switch wasn't working on all the different settings.
first thing was to turn the breakers off. then pull the range away from the wall. used an 1/8 th inch socket to take off the back panel to get access to the switch.used a Phillips screwdriver to disconnect the switch under the knob in the front. took off the wire terminals one at a time and matched it to the numbers on the old switch.replaced the knob, screwed it on to the range. turned the breakers on and tested the switch.worked fine, replaced the back cover and pushed it back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- German from Houston, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
I could can not control the burner
was easy open the back side of the range and change the part, the only issue was the wire I used the diagram
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from American Fort, UT
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner switch had gone bad.
I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Mineral Wells, TX
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bake Element burned in to stopped working
Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.
Was this instruction helpful to you?
Thank you for voting!