CRE3890LSB Crosley Range - Instructions

Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !

Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

Twisted replacement bulb into place easily. Let there be light!

At the Frigidaire parts website, I found the parts and saw that there are videos that show how to replace the burner controls. In brief:
1) Slide the range/oven out so you can get to the back of the control hood.
2) There are three screws that hold the cover in place (the video showed four).
2a) The video also suggests using a #1 square bit. I found that there was indeed a square hole in the caps of the screws, but they also had a hex head that a 1/4" hex nut driver fits. So I used that.
2b) Be careful taking out the last (top center) screw. When it comes free, the cover can drop and bruise or cut your foot or the floor. Having a helper is worth it!
3) The switch for the larger elements has a red dot on front and back. Match it with the one in place that has a red dot. The switch for the small element doesn't have a dot.
3a) Holding a new switch in your hand, remove one wire at a time from the switch in the control hood and put it in the same place on the new switch. I found that for my stove, there was a fixture holding two wires and another holding three wires. This made it impossible to put the wires on wrong.
3b) When all wires have been transferred, pull off the control knob in front and unscrew the two screws that hold the old switch in place. Take out the old switch and replace it with the new switch.
3c) Use the two screws to attach the new switch in its place and replace the control knob.
4) Repeat for as many switches as you purchased. I did all four.
5) Replace the cover.
6) Slide the range back into place.

I found black deposits on all the switches, that must have come from a contactor inside, so I was glad I replaced them all.

Another tip: while the unit is out, clean off the sides and back that you couldn't get to while it was in place. For us, this took as long or longer than the steps above for replacing the switches.

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

went to utube to get instructions on the exact oven we have,fairly easy

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

Replaced switch by according to video with no issues, Terminals were nearly identical as the new switch.

The terminals on the new burner were not located in the same position as the terminals on the old burner. I had to reference the wiring diagram to locate the correct wire to terminal location. There was not enough slack in the wires to position the new burner in the same position as the old burner. I had to rotate the new burner so the wires would reach. This cause me to have to rotate the warming burner because rotating the new burner, the terminals interfered with the terminals on the warming burner. I also had to reposition some of the wires so they would not contact the burner and terminals.

With no install instructions (NOT good for diy-ers), looked through reviews and watched video for help. Replacement part - not same as original. Had to use magnifying glass to id the terminals / take a picture before disassembly. reassembled - found out terminals are different & black wire is too short. Took off element - rotated the clips one number counter clockwise, reassembled - removed black wire from harness for extra reach. Hooked up, lowered top for test. power on - everything OK. Power off - complete assembly. Power on - test. Seems to be good. When I called customer service for assistance because there was no instruction, they told me I should contact a local appliance repair person. (big joke).

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Disconnect power to Range at Electrical Service Panel control box. Remove 240 volt service electrical plug to range. Remove back top panel to expose element control switches. Remove element control switch to L.F. burner by first pulling off the control knob. You may need to use a large flat screw driver to pry behind knob to get it started but it should come straight off. There are two screws revealed under knob that need to come off. Then the element control is easily, but carefully, removed out the back. Be careful you do not pull the "Hot Surface Indicator Light" switch off right above the element control switch. If you do, this will break the end off the plastic "Hot Surface Indicator Light" lens. If this happens you can still replace it but you will need to use super glue to make the "Hot Surface Indicator Light" switch stay connected to the clear lens. Install new element control in reverse order before gluing the "Hot Surface Indicator Light" switch as stated above or you will knock it off again. While holding the old element control in your hand with wires still attached, remove one wire at a time (making note of the location code for each wire) from old element control and install on new control. The new element control layout for the wire prongs will be different so you need to make sure you look for the code (like L1, H1, P) located on each prong location and put the same coded wire from old element control location onto new control prong code location. Reinstall new element control (with wires pushed fully onto prongs of new control) into panel with screws removed before. Reinstall knob, reinstall panel cover and reconnect range power plug. Restore power to Range at Electrical Service Panel control box With electric power restored, test element control by turning it on and see if it properly cycles on and off at different settings. If working properly you should be able to hear it click on and off and element heating and going off accordingly.

Replaced the dual element switch and that fixed it up