CRE3860LWD Crosley Range - Instructions

This should take approx 15-30 mins. It took me 1.5 hours as I pushed the terminals into the wrong end of the block. It's very difficult to get them out when you do that... However, there are no easy instructions on the block or in the instructions to tell you which end to push the terminals into!!! So, with a 50:50 chance of getting it right, I got it wrong. I think most people would need to buy a new part if they do this. It would be very much easier if the block, had an arrow that simply said IN here so that this type of simple mistake is less easy to do... If you get that right, the fix is quite and straight forward. Good luck.

shut off power to stove. Opened the oven door, removed the racks. removed 2 screws holding the element in place. gently pulled element out to expose connections. removed connections. discard old element. reattach connections to new element and reinstall. very simple.

Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.

i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.

I opened the door of the gas range and slid the rack in. No one can do this! I am amazing.

move the range out and unplug power supply, removing the back cover allows access to the probe, this can be done with screw driver or nut driver, loosen clamp that holds power cord in place and move backing out of the way, be careful sheet metal can be sharp, locate the probe unplug the connector and remove screw holding probe, pull old probe out install new probe, fasten down and plug in connector. attach backing and tighten clamp on power cord, plug in to power supply, turn on oven and give it several minutes for probe to work, it took only 20 minutes to replace the bad probe and the oven works like new hop this helps

The old element burnt a hole in itself and just glowed in an area about the size of a quarter. I unplugged the oven, removed the two screws that held the element and removed it. I plugged the oven back in so we could use the top burners. When I went to install the new element I did not unplug the oven as the controls were off. I did not know the element was hot from the outlet (by design) so when I tried to attach the new element sparks flew and it welded itself to the wire so I jerked it looose. I then unplugged the oven, replaced a blown fuse, and installed the element.

removed old terminal block . cut wires and spliced new terminal block and insulated with shrink wrap. Very eazy

Removed the broken door handle with a screwdriver, replaced the new door handle with a screwdriver. Took less than a couple of minutes to make the repair.

I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.

Watched your video and quickly made the repair. I did have to remove the back of the oven (4 screws) to connect the electrical leads to the element. Frigidaire uses a wire harness that prevent you from pulling the wires into the oven to disconnect them as the video shows. No problem; a really easy fix.

removed element , cut wires, conected wires,replaced element

After 15 minutes of frustration and back breaking I removed the oven door and had much better access to the panel, from there on it was all down hill.

First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

First i removed the two screws that hold the element
in place. I the pulled the element out about 3 inches and disconnect the 2 wires. The new one didn't come with the little holders at the front of the element and were very hard to get loose from the old element .i finally got them back on the new one and put it back in the stove. Pretty simple job though.