C31315VBV Crosley Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Can Francisco, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
corroded burners
Unscrew the burners an install new ones! Anyone could do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ramiro from Bernalillo, NM
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Replaced burner
Went well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Staten Island, NY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original burner was eroded on the bottom and flame was coming from undernealth the burner
Very easy. I disconnected the original burner with one turn as well as the two wire connections for the electronic igniter. I then connected the wires to the same positions on the new burner and placed the new burner in place with one half turn to match the indented openings to secure the burner tightly in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhoda P. from Secaucus, NJ
- Parts Used:
- WP3413F018-19, WP3401F075-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from MOUNT HEALTHY, OH
- Parts Used:
- 12001655
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had an F2 message go off then F3 when I tried to turn the stove on
Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- javier from Santa Ana, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bad Gasket
I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from haskell, NJ
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
F 3 signal on display pad every time oven warmed up
Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Westcliffe, CO
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven did not heat up in bake mode.
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Clymer, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not turn on
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from DAYTON, OH
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Gas would come on, would not ignite. Oven not heating.
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from CINCINNATI, OH
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The oven igniter would glow red but gas did not come on to light the burner.
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from AURORA, MN
- Parts Used:
- 12400035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
No heat in oven
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Israel from HYATTSVILLE, MD
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The igniter of the burner was worn out of constant use.
First I did was to google the problem I have. There several video how to solve the problem. It show me different ways to solve my problem. I just follow the instructions. Thank to google without it, I am lost. I may add, that google is a big saver for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Cocoa, FL
- Parts Used:
- 12001596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burners would not lite
I removed the old module ,replaced new bracket,crimped new wire lugs on wires. being an electrician for 50 plus years helped. Thanks Lloyd
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Arlington, AL
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven was slow to get to temp and not holding temp
Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.
Was this instruction helpful to you?
Thank you for voting!