CE35400ACV Crosley Range - Instructions

Easy to put into place and done....Could have called this in, because place of business is in Louisville, close to me. Delivery was quick.

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.

Turned off the circuit breaker. Removed two screws - pulled the element out enough to get to clips connected to power. Removed old element - installed the new one. Replaced the screws, then turned the circuit breaker back on. Stove was repaired.

Easily removed the oven and had access to the rear in under a minute undid the 2 Phillips screws retaining the element and replaced with the new element I had ordered it was just so simple!

Thank you as you saved us calling out an expensive technician avoiding unreasonable time and costs expenditure

unscrewed element from oven, traded wire connections to new element, screwed new element in - saved myself a $75 service call

Shut off the power to the stove. Remove the two screws retaining coil
And simply pulled the coil out exposing the wire clips. The wires detach easily
Reconnected to the new coil, pushed the coil back in, reintalled the retainer screws and
Done. Time: ten minutes

repair was easy- turned off power at electrical box, emptied out the wire shelves in the oven. Unscrewed two fasteners holding element in place, pulled element out about 3 inches, unplugged electrical end connectors.
Then got new part, attached two electrical connectors, slid back in place, fastened with two screws, turned power on and we're baking. I believe this part would be covered under my warranty- but we were having a party that weekend and I could not wait for the repair guy to do this on his schedule, plus his labor alone would have cost much more than my part and next day delivery.

I ordered the part and it came in within 2 days from fedex! Great timing. It took me all of 10 minutes to fix the coil at the bottom of the oven. Fixed the problem and had plenty of time to cook dinner before my husband came home!!
GREAT SERVICE AT THIS SITE! They knew the right part! And the instructions are very simple.

Thank you

we removed the back I had my dad help me so he removed the wires while I removed the screws on the inside. When I received the part he also helped me replace it by putting on the wires while I put the screws in. Remember to disconnect from electricity.

First I fliped the curcuit breaker to eleminate power to the stove. Then removed the 2 screws that hold the element in place. Then carefully pull the element out and disconnect. Installed new element to connectors and gently pushed back into the stove housing. Secured with the removed screws and turned back on the curcuit breaker. Turned on the oven and it worked like a charm..

Very easy, with only the removal of 2 screws.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) One of the wires came off before i was able to pull the element out far enough. I then had to take the back off (2 screws) The total repair took about 5 minutes