All Installation Instructions for Crosley Range VRGW3162RB0

Customer:: bobby from HERSCHER, IL
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

range would not heat right

very easy watched the howto you gave

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: ROMMEL from GLASSBORO, NJ
Parts Used:: W10857234
Difficulty Level:: Very Difficult
Total Repair Time:: More than 2 hours
Tools:: Screw drivers, Wrench (Adjustable)

Door mechanism was not working properly. It has to be change to a new one.

Take off the oven door from the unit. Disassemble part of the problem area. Arrange the different parts and screws orderly to have a transition from taking the parts off and putting it back.
I watch a video several times too. BUT THE MOST IMPORTANT IS PARTS SELECT HAS THE RIGHT PART I WANTED AND IT ARRIVE PROMPTLY.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Benjamin from RANBURNE, AL
Parts Used:: W11590294
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver

Igniter quit

I did it from the bottom instead of through the oven.
Less work than pulling out the trim. Had to bend a piece of metal.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: William from KRONENWETTER, WI
Parts Used:: W11590294
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Igniter was not getting hot enough.r

Take off back plate on stove unplugged igniter wire take nut drive remove old igniter run new wire through hole plug in replace back go inside stove and install new igniter.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jim from WAUSAU, WI
Parts Used:: WPW10535767
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

broken inner door glass

glass had 2 dirfferent sides didnt know how to place in door menards still sold same oven so went there and checked out how to place in door.my biggest problem was door was ordered saturday evening was shipped on monday from st paul by fed ex alright 3hrs 160 miles away should be here tuesday. from st paul it went to chicago area 230 miles away to oak creek wi 180 miles away somewhere along the line handed over to US
post office which delivered it on friday..

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Gregory from BRIDGEBORO, GA
Parts Used:: WPW10181986
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Oven temperature was 50 degrees off

Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Joanne from Negaunee, MI
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Dave from Titusville, FL
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

Was this instruction helpful to you?

Customer:: Paul from Cornelius, NC
Parts Used:: WPW10181986
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

oven temperature did not stay as set

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

Was this instruction helpful to you?

Customer:: Ken from Las Cruces, NM
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven shutting off after temp reached 350

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Was this instruction helpful to you?

Customer:: Richard from Wooster, OH
Parts Used:: WPW10181986
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Stove kept turning off

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Was this instruction helpful to you?

VRGW3162RB0 Crosley Range - Instructions