CG31400ADW Crosley Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Fred from Suwannee, FL
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven very slow to light on bake mode. Gas smell.
First I removed the bottom plate in the oven. The ignitor was located at the rear of the burner and I removed to screws and it was loose except for the two wires. Next I removed the bottom tray from the stove. Two screws held the metal guard in place at the rear of the stove. After removing the plate, I determined which wires belonged to the ignitor, unplugged them at the coupling and pulled the wires out through the bottom of the oven. Replacing the ignitor was simply to reverse the proceedure. PartSelect got the part right out to me, installing the new part was a breeze, and my wife calls me her "hero." This site was a real help and saved me a service/repair bill. Thanks!
Fred
Fred
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Forked River, NJ
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Smell of gas and would not always light or took forever to preheat
Remove the oven door by opening halfway and lifting door away from stove. Removed racks and bottom pan from oven area exposing the gas bar and vertical mount igniter. Next remove bottom storage door. With phillips screwdriver remove 2 screws securing rear cover plate in back of storage area, accessing the igniter connection, and unplug the plug. Next back in oven, remove 2 5/16 sheet metal screws securing igniter with a nut driver and remove igniter by getly pulling disconnected end thru to oven. Now reverse process, install new vertical mount igniter and push connection down thru to storage area, then reconnect wire connection and put cover plate back on.
At this piont I turned oven on and checked igniter, it glowed red right away and the oven lit right up. Put storage door, oven door, bottom oven panel, and racks back in and done. Took 15 minutes tops, and anyone can do this, super easy. My oven would sometimes take half hour to preheat to 350,if it even lit, now 5 minutes, and it lights every time. Save the cost of a repair man folks, this one can be done by any weekend warrior.
I would just like to note....if you are uncomfortable with disconnecting wire plugs and plugging them back in, just unplug the oven from the wall as well before changing out the part, just to be safe.
At this piont I turned oven on and checked igniter, it glowed red right away and the oven lit right up. Put storage door, oven door, bottom oven panel, and racks back in and done. Took 15 minutes tops, and anyone can do this, super easy. My oven would sometimes take half hour to preheat to 350,if it even lit, now 5 minutes, and it lights every time. Save the cost of a repair man folks, this one can be done by any weekend warrior.
I would just like to note....if you are uncomfortable with disconnecting wire plugs and plugging them back in, just unplug the oven from the wall as well before changing out the part, just to be safe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Godfrey from new york, NY
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
The igniter was just glowing and it didn't open the gas valve
I removed the screws and unplugged the connectors and i inserted the new igniter which was glowwing much brighter than the old one which gave me an indication that it has the amount of temperature to open the gas valve.Idid a good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecil from REDFIELD, SD
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
j just look at it and figure how itcomes apart and reverse when installation complete easy
took out burner and remove ignite r and reinstall a new one simple as that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacey from Woverine Lake, MI
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven wouldn't heat
I removed the floor of the oven (one screw) and the heat dispersal shield (one wing nut). Then I detached the old igniter using a socket set. I had to remove the bottom drawer to unplug the ignitor and plug in the new one. Then I reassembled. Total piece of cake and I have no experience whatsoever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Gloucester, MA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Broiler would not ignite
I shut the gas off and removed the oven door pulled the oven out and removed the electrical access panel.
unpluged the igniter and removed the 2 screws holding the igniter and relpaced repluged.
right to self clean mode. Easy job no worrys
Be safe check your gas connection!!
unpluged the igniter and removed the 2 screws holding the igniter and relpaced repluged.
right to self clean mode. Easy job no worrys
Be safe check your gas connection!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Goshen, IN
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The main gas valve to the oven would not stay on.
Remove oven door, pan drawer, oven racks, bottom pan, flame spreader. Remove valve cover at back of pan drawer. Unplug old igniter. Remove two mounting screws holding igniter to gas tube assembly. Install new igniter, plug it in, and reassemble. Easy as pie! Oven works better than it has for a looooong time! Heats up to 400 in 5 minutes. Wife is happy! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Mokena, IL
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
old igniter wouldn't get hot enough to allow gas flow
Nothing to it - remove oven bottom, and burner cover, unscrew the 2 scews holding the igniter
(one of mine sheared off now only one is holding the new igniter in - it still works) unplug wire at the connector then reverse and the oven is as good as new. The best part is that I received my part in only 2 days.
(one of mine sheared off now only one is holding the new igniter in - it still works) unplug wire at the connector then reverse and the oven is as good as new. The best part is that I received my part in only 2 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willi from Old Saybrook, CT
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from WOODBURN, OR
- Parts Used:
- 74004053
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Back burner would not light
I replace the igniter first that didn’t work so I had to order the wiring and then I replaced that there was a cover that I took off with a screwdriver took the wiring off and put the new wiring in it it was that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from San Juan Capistrano, CA
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The floor panel of the oven was pocked and in bad shape
I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tao from Frisco, TX
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the shell if the igniter was broken
find the part (image is really helpful), buy, and replace. Like I said, it's really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W from Jonesboro, GA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven pilot glow only
Open oven door remove trays.. remove floor of oven...remove single screw holding heat shield... unscrew two srews holding ignitor and unclip plastic...done..reverse to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Fort Dodge, IA
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not ignite
Removed bottom tray in oven, used nut driver to remove igniter, pulled oven out from wall and unplugged cord, did steps in reverse and repair was done. Very good tip on what was wrong with oven and how to diagnose the problem. I will defintly use your tips and purchase parts from you in the future if the need arises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from rochester, NY
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Long delay before ignition slow preheat
Remove oven floor and bottom drawer
remove 2 1/4-inch screws holding ignitor
remove cover plate behind drawer to access P/J
Disconnect plug remove ignitor and reassemble
Did not have gas smell, but ignition took 6 minutes
remove 2 1/4-inch screws holding ignitor
remove cover plate behind drawer to access P/J
Disconnect plug remove ignitor and reassemble
Did not have gas smell, but ignition took 6 minutes
Was this instruction helpful to you?
Thank you for voting!