CE3832SRW Crosley Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frances from MOREHEAD, KY
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace broken bake element
Unplugged the range. Took our the oven shelves. Unscrewed the bars holding the broken bake element to the back of the oven wall. Gently pulled out the wiring to which the bake element is attached. Slipped the ends of the broken bake element off the ending on the wiring. Then slipped the ends of the new bake element over the ends on the wiring. Then pushed the wiring with attached bake element back into their position behind the oven wall and attached the bars holding the bake element to the back of the oven wall. This is really easy because it is exactly like the on-line video, for I am a 75 year old female with little technical experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra Collignon from SANTA CLAUS, IN
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Drip Pans were stained and burned on.
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from ROCKTON, IL
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace the lower oven element
Unplug the 220 cord..remove rear metal back ( 7-8 Ph/screws)... disconnect the red & yellow connectors from the back of the lower element. Remove-the-lift-off Oven door. Remove the two Ph/screws (one on either end of the element) At the very rear of the oven. Install the new element and reverse the about to reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Schertz, TX
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake element would no longer heat up
I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from BOULDER, CO
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake element burned out
Removed the failed bake element per the video linked in the Partselect email. Unlike the video on YouTube the PartSelect video shows that the bake element can easily be replaced through the oven door and it is not necessary to slide the range out and remove a rear panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicki from ELSIE, NE
- Parts Used:
- WPW10196405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
No problem Took off old ones and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from ROCHESTER, IN
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element had burnt in half.
Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from PATERSON, NJ
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Element didn't heat at all
Removed 2 screws, disconnected wires, attached wires to new element, put screws back. Turned oven on. Perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Ottawa, OH
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out.
First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tawnia from SHOW LOW, AZ
- Parts Used:
- WPW10259868, WPW10196406, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface element needed to be replaced along with all the drip Bowls
take out the old put in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kiara from JACKSONVILLE, FL
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Baking Element won't heat to bake.
I had the problem before and had to call in a Tech to repair the baking element in my oven. It cost me $150.00 for the repair. This time I decided to do the repair myself, so I went online and found this site The instruction video made it very easy. I am very proud of what I was able to do without calling a Tech. My oven works like new, It only cost less than $40.00 for the total repair. I am so glad this site were there when I needed them.. Thanks a Lot..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion J. from Palmetto, FL
- Parts Used:
- W10196406RW, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing old drip bowls
It was so simple & the parts fit perfectly. I appreciated all the help from your sales lady. Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paola from High Bridge, NJ
- Parts Used:
- WP12001560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just plugged the burner in and it was good to go.
The burner wouldn't work. I just plugged in the new one and all was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Allyn, WA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned in half
Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hudson from Cockeysville, MD
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The element was completely gone.
Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.
Was this instruction helpful to you?
Thank you for voting!