CE35400AAQ Crosley Range - Instructions

Moved the stove, unplugged it. took the back off, took out old board installed the new one. It was just that easy and saved us from buying a new stove.

Disconnected power to the range, Took off the oven door removed two screws and disconnected the two electrical connections to the heating element. Made the two connections to the new element and replace the two holding screws. Replace the oven door and plugged in the power cord. Turned on the oven to test and was finished.

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.

just plugged it in!

Power turned off. Door of the oven lifted off. Four screws removed, old element pulled out to reveal electrical connectors. Wires easily removed, and element discarded. New element connected to the two conductors, four screws installed and the job was completed.
Very easy. Took about 10 minutes.

This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.

It is very easy shut off the power yo the stove at the fuse box, unscrew the two screws and pull the element out replace and screw back into place.

Turned the power off to the oven, unscrewed the ends of the element, connected new element, screwed it back in to place and turned the powe back on. The video provided in my shipping confirmation was very helpful.

I unplugged the cord to the stove. Then I removed the two screws on the broken heating element. Once the screws were removed, I slid off the two wires attached to the element prones. Grab the new element and attached the two wires. Reinstalled screws. Plugged in the cord, and turned on oven. Heating element came on.

Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.