CG31200BDW Crosley Range - Instructions

First I slided the door off it's hinges to make it easy
to get to the two screws holding bottom trim on
remove these screws slide in new glass replaced the trim and installed the two screws.
piece of cake total time 10 -15 min.

I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.

Made sure the knob was in the Off position.
Removed the old knob by gently pulling it off.
Lined up the knob and pushed it on.

I just pop on the new knob. It was easy. And I got fast service order my knob and it got here in 3 days. I am very happy with your part and service. Thanks Donna Eden

It was easy since it just pushes on...

I pulled the knobs off and put the news one on. It couldn't have been easier. From my order to the fast shipping and helpful staff, I was completely happy.

PartSelect will be my first stop for all of my appliance repairs.

Thank you

Not much of a repair, just put the new one on. What I would like to share with you is the great ease of using Part Select Website. A stove knob you say? Well it seems like an easy part, but actually there a hundreds or more to select from. I could not find the model number on my stove. So I started looking through the site and it gave me options to choose from to narrow down the search. Being able to enlarge the part was extemely helpful, between 4 parts, I finally found the one that fit my stove. Might seem like not very much to you, but I was so happy that I finally found the part, it is the right part, and I don't have to mess with that stove thermometer anymore! The process was very easy, delivery was fast and I am one happy customer. Thanks Part Select! Debbie Watson

Matched up knob. 3D picture helps bunches

I couldn't find my model number U31EA-7 so I decided to go with a deferent model number U31FA-7 Pulled the old Knob off and pushed the new knob on and it works great

Popped in there real quick. Wish I would have done it sooner, my oven heats up much faster.

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

Shut off the gas before you do anything! Remove the top front face cover by removing the four screws. Remove the three gas lines that go into the oven valve. remove the screws that hold down the manifold bar. Slide bar to the front and free from the burners and main valve. Remove the small bolt on the underside of the manifold that holds in the oven valve to the manifold. Remove old thermostat bulb from it's bracket inside the oven and pull through to the top of oven. Then remove the old valve. Remove rubber seals and transfer them to the new valve if you don't have new ones. Replace the new valve. Insert thermostat bulb on the end of the wire into the hole and down into the oven. Mount thermostat bulb into bracket. Then just reinstall in the same order that you took it apart. Then run the oven and check the new thermostat out to make sure it is working properly.

finished removing door seal, used pliers to remove old securing studs. positioned new seal and pushed securing studs into existing holes and was done.

I was pleasantly surprised that the knob I ordered from you was perfect. Your catalog picture/description was right on. I am so grateful I found your site. I looked @ others and they did not compare to your thorough description. Thank you.

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.