RSS358ULG-P1130891NL Caloric Range - Instructions

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

I took oven door apart and replaced old gasket with new one.

I am writing this post to hopefully save someone else the frustration and confusion I experienced when I ordered a replacement ignition module for an Amana gas cooktop AKGD3060WW. Over time, three of the four burner would not light. I ordered a replacement spark module from PartSelect and to my surprise it arrived the next day.

The installation instructions were very confusing. I read the instructions posted by prior customers about this part and none of them helped or seemed to apply to the same cooktop. With the use of the exploded view on PartSelect website I was able to figure out where the module was located.

I turned off the gas and unplugged the unit.

I had to go under the cabinet and securely prop up the cooktop cavity box from below as I had to take off the whole cover, which was actually holding, or mounting, the unit to the counter top.

I removed the cooking units then, the control knobs and the glass control plate, and the vent filter and vent cover. After removing about 20 screws from the main frame/cover I located the spark module at the rear of the unit, sandwiched between two pieces of sheet metal and obstructed by numerous wires. I recorded the wire connections then unplugged the module. It was difficult to remove module due to the numerous unrelated wires that were routed through that area.

I connected the wires to the new module (NOTE: The replacement module has no terminal identification.), plugged the cooktop into the power and tested it and noted that all four burners now received a strong spark.

The original unit is smaller than the replacement unit and the supplied bracket does not fit this cooktop. I had to force the module into position. I removed the two small tabs and applied double sided tape applied to the bottom then secured it against the original mounting bracket. I then adjusted the wires back into the recess with the module and reassembled the cooktop.

The cooktop now lights all four burners instantly, for the first time in several years.

I used the instructions that were online at the PartSelect website. Perfect instructions. It took longer to clean the unit than installing the new paart.The instructions that came with the part were not that useful.Thanks to PartSelect, my wife is now happy.

Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.

Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.

Removed the burners 2 screws per burner disconnected the wires to the burners. Lifted the oven top off removed original ignition module. Installed wires to the new module taking note of replacement location. Than mounted new ignition module. Tha only hiccup was dropping 1 screw down into the stove lining found replacement screw and installed module. Cleaned and replaced top. Mounted burners and the stove is working like new. Project proved to be quite simple and guick. Thanks to partselect for there prompt delivery and other peoples input on install made it quite easy and simple,

removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine

Using a meter, we determined each of the four igniters had continuity from end to end and also had continuity from the end of each igniter back to the spark module. At that point we decided the module was probably bad and, after reviewing some similar-sounding problems on this website, I ordered the module. Installation was simple and solved the problem. All four burners now ignite as they should. One caution - the installation instructions that came with the new module did not describe anything like my stove.

First, unplugged the cooktop from outlet and shut off gas. Then, removed burner assembly then located and removed existing spark module. Installed new spark module kit, reassembled burner assembly and then plugged unit into electricity and turned gas on. Was rewarded when testing burners with an instant ignition.

I had already removed the old hinges by removing the screws/bolts and removing the broken hinges from the back side through the drawer below the oven that I had already removed. Took the new hinges and screwed the two metal screws into the top hole on the new hinges after placing hinge in vise, one screw on each then removed them and placed them to the side. Determined the right tap from my tap set, and then tapped the bottom two holes on the new hinges, one on each. Placed the bolts that came with the new hinges into the holes I had just tapped, screw them in, then I removed them and placed to the side. Took hinges and bolts / screws to the oven, inserted hinges in through the drawer that I had removed up to each side where hinges would come back out to the front of the oven. Placed screws / bolts one at a time through oven door frame into the hinge on the back side, and then threaded them into the hinges and tightened. Replaced oven door onto new hinges and checked for correct operation. Door works like new.