ESF32002W (P1130944NW) Caloric Range - Instructions

Removed screws holding rear cover, removed cover. Male connector on Broil Element had rusted off and caused wire to fall onto the frame of the range, shorting it out.

Removed element by disconnecting other wire and removing the single Phillips head screw accessible from inside the oven. Released the element from the two hooks towards the front of the oven near the door and removed.

The wire to the element that burned off had a high temperature female push on connector that I did not have on hand. I had a high temp ring connector so I drilled one of the male connectors on the new element so I could use a small stainless screw and nut which I had to hold the ring terminal on.

After crimping the new connector on I fastened it to the element, connected the other wire and put the rear cover back.

Good to go now!

Shut off power to the oven.
Unscrewed the old broiler element, unplugged it.
plugged in new one, screwed it in.
Turned on the power. Voila!

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Turned power off! Removed two mounting screws, disconected two slip on wire terminals from heating element. Removed Element from oven. Took about 10 minutes.
Part came in two days. Re installed heating elemet by pushing on the two slip on wire terminals and re installing the two mountint screws. Took about 10 more minutes.
We have been retired for 17 years. Wish all my "Honeydew jobs were this easy!

The repair went real easy. Turned off power, unscrewed two screws at back of oven and disconnected the two wires. Reconnected two wires to new broiler element and remounted the new one with the two screws. Turned the breaker back on and had a steak cooking in no time.

Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

Removed two screws securing heating element. Removed broken element and disconnected wires. Removed back panel of oven, unplugged from outlet, installed new element, attaching 2 screws. From back side of oven reattached 2 wires, replaced back panel and plugged in. Pretty simple!

had to slide the range out from the wall and pull the electrical plug, then using a nut driver ,I removed 9 screws from the back panel and removed the back panel to expose the bake element wiring, had to remove the three wires connecting the power cord to the range terminals a/c the back panel would not fully come off with these wires connected. i then pulled the 2 stake eyes from the element, unscrewed the 2 screws
securing the bake element from inside the stove and removed the element, re-installed the new element and screwed into place, attached the
stake eyes on the rear of the element and re-attached the power cord, put the back cover back on and plugged the range in., tested and the range functioned as intended.

It was simple. I flipped the circuit breaker just in case, and then unscrewed the bracket for the old heatng element. Disconnected the two plugs, connected the plugs for the new element, and screwed the new bracket back in.
The saleslady assured me when I was purchasing it from PartSelect that it was pretty easy. That gave me the confidence, and she was telling the truth. I will purchase again from Part Select....although I hope I won't have to do so for a while.

After receiving the part I was able to quickly remove the old piece and replace with the new. For this project you have to remove the back of the oven to remove the electrical attachments.

I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.

First, I unplugged the power cord from the receptacle. I then removed two philiphead screws that hold the element in place. I the pulled the element out about an inch and a half . I then disconnected the the two wires from the element. The I connected the replacement element and resecured it with the two mounting screws. I assured everything was correct and then I plugged in the power cord and turned the oven on low heat to give it a test. Everything workout just great. The part was just what I needed.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Plug the wires onto the new bake element and re-screw back into place.

I turned off the breaker and unscrewed the element. Removed the plug connection and once I got the correct part, we plugged it in, screwed it back into the oven wall and done! I am a single female and was able to replace the heating element in a short amount of time with assistance from my 16 year old son!! I was very surprised at how easy it was to repair. The key is to get the correct part the 1st time!