P1132637NW Caloric Range - Instructions

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

Had to use wd-40 to get the old part loose (oven is over 15 years old) and used pliers to pull apart from the oven. Replaced with the new part and works great. . . Once I used the wd-40 to loosen, it was super easy.

Unscrewed the 2 screws in the back of the element. Disconnected the unit from the bake of the oven, replaced the two ends of the new element and screwed in the 2 screws. Oven works great! Took less than 5 minutes to complete.
Thank you for the FAST delivery!!

This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.

I read up about the repair on the internet and what it entailed, thought I could do it. So followed directions from the internet after looking up Ammana, model number and serial number, and ordered the part from Part Select.com. It arrived two days later, was really impressed with their business handling of it.
I paid particular attention to disconnecting the power and pulling the plug out of the wall as double insurance to not getting electrocuted.
The Installation was quite simple, just pull the old one out and put the new one in. I took note of how the old one came out, and connected the new one in the same fashion, and it works wonderfully, just heated right up. It was a good experience.

took out old element, replaced with new.

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

Slide stove out and unplug. Using nut driver (phillips screw driver would work fine) remove screws securing back panel. Remove back panel. Pull off wires from heating element. I made a lose knot on left wire so I could install as removed without confusion - sometimes it matters. Removed 2 screws securing element inside the oven. I installed everything as it was - oven works great. I saved over $100 and my wife thinks I'm a genius. Hardest part was cleaning accumulated mess behind the stove.

my wife did the the job and it was that easy. she took out two screws sliped the wires off put the two wires back on and put the screws in . She is a bank teller and teachers water aerobics

While trying to clean the oven, I decided to remove the lower heating element to make it easier. After removing the 2 screws on the bracket that holds the heating element in place, I pulled the heating element out only to short it out on the back of the oven and wreck the element. Luckly I was not injured or shocked, so if you need to do this, I recommend reading the owner's manual on how to property ground out the circuit first.

Anyways, to replace it, I just removed the lower panel on the back of the oven (roughly 10 screws). Installed the new element on the inside of the oven and screwed it into place. Then, connected the wires to the element from the back of the oven. Replaced the panel and turned the power back on.

In all, it took probably 15-20 minutes to fix and only cost me $37. I know that a minimum repair cost for this from Sears would have been $150, so definitely worth my time.

We unscrewed the old element by removing 2 screws and put the new element in place and put the 2 screws back in and it was done. Piece of cake!

This repair took less than 5 minutes, literally! Two screws released the element, then unplugged it from two connectors. Then plugged in the new unit and screwed it into place. Cheap and easy!

Removed 2 phillips screws and pulled elements out 3 to 4 inches. One of the leads touched the housing and blew the circuit breaker, so don't forget to unplug or turn the breaker off! Simply slide clips off and install on new element. push back in place and reinstall 2 screws. Very simple.
P.S. element was delivered very fast!