RSF3300W-P1141265N Caloric Range - Instructions

Screwed in light bulb and glass protector

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

unscrewed the bracket holding the igniter in place then we pulled the drawer on the bottom out and disconnected the Igniter - then we took the unit out of the bracket replaced it and then put the bracket back into place screwed it in and reconnected the igniter and now it burns hotter then it has since we moved into the house two years ago.
I was worried that it would be a hard long job but was pleasantly surprised when it only took a few minutes.

Took off oven door, took out racks and bottom plate, removed burner assembly disconnected wires, removed old ignitor put new one in holder, connected wires, put burner assembly back, checked if it worked and replaced racks ect..No tools needed.

First I turned off the gas supply to the oven and disconnected it. I then pull the oven out away from the wall. I then unplugged the power cord. I removed the oven door by lifting it off of it spring hinges. I then removed a lower plate that covers the burner element by pressing in a manner that it popped off. I then located the ignitor and removed 3 screws. All were easily removed. Carefully, I pulled the igniter out and removed the wires from the wires that supplied the current to the ignitor. Installation followed by working the steps above in reverse order.

I researched the needed part (igniter)and purchased it on line. It arrived promoptly. I called a repair person who arrived and installed the new part. All is well.

Removed old igniter held by one bolt & nut, diconected two leads to igniter. Gas mainifold remained in place during repair. Replaced with new igniter, using old mounting bracket and wire ties. Total repair time 30min, oven repair service wanted to charge $80 just for diagnosis. Total cost of repair doing it myself was $50.

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

I took oven door apart and replaced old gasket with new one.

The first igniter was received broken. A replacement was received within 5 days. It was very easy to install once the protective cover was placed over the igniter end. In my opinion, this part should be sold with the protective cover already in place.

I used the instructions that were online at the PartSelect website. Perfect instructions. It took longer to clean the unit than installing the new paart.The instructions that came with the part were not that useful.Thanks to PartSelect, my wife is now happy.

Used grinder to cut the screws. All 4 screws had to be cut to remove from burner assembly. Once this was acomplised it went fast with no problems

First, my wife and I pulled out the oven from wall to disconnect electric plug and, also with a wrench; I shut off the gas connection on the wall. I then removed front door of the oven by pulling up on door to have easy access to lower part of oven, and then removed pan to get to Igniter. Removed the three screws on cage that supported the Igniter and, I also had to remove several screws to the manifold and bottom pan that supports the manifold so that I could disconnect Igniter. I then was able to pull out old Igniter and, reconnect the new one. After that, I reinstalled everything in reverse. Before pushing oven back into wall; we made sure the new igniter worked. It worked just great. My wife and I were so happy and proud that we done it our self, and not have to call someone to do it for us. It took me and, my wife about an hour and a half to complete the job. I believe the reason it took us as long as it did was because we really didn't know what to expect. Now that we know; I am sure that we could do it again in 30 to 45 minutes. Dave & Marsha; 8/23/2013

I am writing this post to hopefully save someone else the frustration and confusion I experienced when I ordered a replacement ignition module for an Amana gas cooktop AKGD3060WW. Over time, three of the four burner would not light. I ordered a replacement spark module from PartSelect and to my surprise it arrived the next day.

The installation instructions were very confusing. I read the instructions posted by prior customers about this part and none of them helped or seemed to apply to the same cooktop. With the use of the exploded view on PartSelect website I was able to figure out where the module was located.

I turned off the gas and unplugged the unit.

I had to go under the cabinet and securely prop up the cooktop cavity box from below as I had to take off the whole cover, which was actually holding, or mounting, the unit to the counter top.

I removed the cooking units then, the control knobs and the glass control plate, and the vent filter and vent cover. After removing about 20 screws from the main frame/cover I located the spark module at the rear of the unit, sandwiched between two pieces of sheet metal and obstructed by numerous wires. I recorded the wire connections then unplugged the module. It was difficult to remove module due to the numerous unrelated wires that were routed through that area.

I connected the wires to the new module (NOTE: The replacement module has no terminal identification.), plugged the cooktop into the power and tested it and noted that all four burners now received a strong spark.

The original unit is smaller than the replacement unit and the supplied bracket does not fit this cooktop. I had to force the module into position. I removed the two small tabs and applied double sided tape applied to the bottom then secured it against the original mounting bracket. I then adjusted the wires back into the recess with the module and reassembled the cooktop.

The cooktop now lights all four burners instantly, for the first time in several years.

Removed the oven doors for access; removed the burner onto which the ignitor is attached, disconnected the electrical wires (power off). Reversed the procedure to put it back together. We are now cooking with gas again. Thanks. Fletcher