ARGS7650WW-P1130765NWW Amana Range - Instructions

Replaced glow bar/ igniter.

First, I removed the oven door (two screws and pulled it off the hinges) and placed it out of the way. Then I removed the baking racks and bottom cover over the heating element this exposed the heating element, easily removed (two screws). I unplugged the old element, plugged the new element in, and put all the stuff back and the put the door back on. Next was the fun part. . . Had to get the wife to turn on the oven (very complicated touch pad - not made for a man to understand), and shazamm the oven came on! Now I can have some of those great homemade biscuits again!

I pulled the racks out of the oven. Then pull the plate off that covers the burner. There is another shield with a nut on it that covers the burner. Removed it.
The ignitor is mounted on the back of the burner, held by 3 screws, remove them. Pull the bottom sliding drawer out completely. (you have to lay down for this). There is a metal plate in the very back held with 2 screws, remove them and pull the plate out. You'll see the 2 high temp wires (White) with a plug connector, simply unplug the connector and you are ready to pull the whole ignitor assembly off the burner. The ignitor ceramic base simply slides out of the sleeve.
Put the new ignitor in the sleeve and put everything back together. It's pretty simple.
This is the second ignitor I have installed in 2 years, hopefully I'll get more life out of this one.
Good Luck.

diagram on website was very helpful. simply unscrew two screws,remove and replace electrode and works perfectly.
Ordered one day arrived next with standard shipping installed before next day supper awesome service

I had changed the broiler igniter several years ago, but it had "burned out". The only thing that slowed me down on this repair was that the igniter was glowing brightly, but the oven would still not ignite. Others have written that it's best to try a new igniter FIRST. That indeed was the solution.

One "trick" that I did not find in other posts was how to get to the plug on the end of the igniter - so here's how.

First, open the oven, remove all racks and the bottom cover. Remove the nut holding the heat deflector in place and remove the heat deflector. Then remove the three screws holding the igniter in place.

Second, pull out the bottom drawer of the ove and remove it. At the very back there is a sheet metal cover held in place by two additional screws; remove them to rermove the sheet metal cover - this will allow access to the plug on the other end of the igniter. Unplug the igniter.

Third, feed the plug end of the new igniter from inside of the oven to the underside. Plug it in, reattach the sheet metal cover, reinstall the drawer, screw in the new igniter and put the heat deflector back in place.

Note of caution: be careful handling the igniter - it's fragile and easily broken.

very simple repair, the oven had the issue about ten years ago, just removed drawer ,removed two screws holding cover plate unhooked power and disconected plug. removed element screws and pulled out old element from holder and inserted new one. re attatched element holder, cover plate, and put drawer back in. works great !!!
My parts wrere shipped promptly and arraived in great condition, stove looks and works like new again

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

We removed the oven protective shield, took out the broken glass (very carefully) and replaced it with the part shipped. Then, we replaced the protective shield and it was done.

The repair was fairly straightforward. The drawer below the oven had to be pulled out and the panel in the rear (looking from the front through the opening where the drawer was) was removed. It was then a matter of removing two screws and unsnapping the wire connection. And then replacing the igniter.

Removed the three screws holding the igniter, pulled the old one out and plugged in the new one. Very simple.

Removed oven grills and top of burner pan. This exposed the igniter. Removed 3 phillips head screws from igniter bracket. Slid old igniter out the back end. Removed utility drawer. Removed two screws from back pan covering igniter plug-in. Unplugged igniter, removed from range. Handling of igniter is tricky..do not touch black end. Slide new igniter into the bracket, feed wire with connector through hole in back (where igniter was removed from), install the three screws for the bracket (your new igniter is now secure), from the bottom, plug in the new connector it only goes on one way. Re-install pan with two screws. Put utility drawer back in..job is complete!!

I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!

Turn the power off to the Stove
Removed six screws from the Baffle Drip and removed Baffle Drip. Removed two screws from the Oven Light Assy. Position the Oven Light Assy to get to the ERC-3. Removed four screws from the ERC-3 unit and separated the ERC-3 unit from the Oven Light Assy. Remove the old Overlay, Mylar from the ERC-3 Unit. Install the New Overlay, Mylar on the ERC-3. Install the ERC-3 back to the Oven Light Assy. Install the Over Light Assy. Install the Baffle Drip and turn the power on to the Stove.

ordered new broiler pan

1. Removed racks
2. Removed bottom cover
3. Removed screws holding ignitor
4. Removed storage draw
5. Removed cover over wires
6. Unplugged ignitor & placed with new
7. Put back together