ACS4250AC-PACS4250AC Amana Range - Instructions

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new wires, replaced the two screws and turned on the oven to test it. Easiest repair job I have ever done.

Slide stove out and unplug. Using nut driver (phillips screw driver would work fine) remove screws securing back panel. Remove back panel. Pull off wires from heating element. I made a lose knot on left wire so I could install as removed without confusion - sometimes it matters. Removed 2 screws securing element inside the oven. I installed everything as it was - oven works great. I saved over $100 and my wife thinks I'm a genius. Hardest part was cleaning accumulated mess behind the stove.

I ordered the new part, which arrived in just 2 days. I did not pull the oven away from the wall, I merely turned off the electric, unscrewed the bad element, pulled it out enough to see the ends, and then I removed the existing wires using needle nose pliers. I put the wires on the new element, inserted it back into the oven wall, and screwed it tight. I turned the electric back on, and checked it out. Worked like a charm! Only 40 bucks (including shipping), five minutes of my time, and I avoided an expensive service call. :-)

my wife did the the job and it was that easy. she took out two screws sliped the wires off put the two wires back on and put the screws in . She is a bank teller and teachers water aerobics

Turned off 230 volt breaker to range,connected old wires to new element ,put back into place replaced the two mounting screws. Turned breaker back on and tested range.

I went online to learn what F-3 meant and it said temp sensor malfunction. I ordered the part - it looked the same so I repaced the old one and then the plugs were different. I cut the plug off the old sensor and cobbled together a connection. I powered up the stove and the burners were ok, but the oven appeared dead. about an hour later the alarm went off and it displayed F-1. I figured I needed to order another part, but hit Oven cancel and the display lighted up. I set the clock, heated to 400 and made a tray of cornbread. It seems to work ok, but I need to make a better arrangement. perhaps cut the new part connector off and splice the old connector. I don't like having electrical tape so close to the oven - it will probably melt with much usage. It is working - for now!

It was real easy. Removed two screws, pulled the element forward, removed to clip on wires, removed element and put the new element in place, replaced wires and screws, turned it on and up to temp. in no time. great service and quick delivery on getting the part.

replaced element

removed the screws disconnected the old one and connected the new one and put the screws back on it

I took a couple of screws out that hold the bottom
element in place replaced the old one with the new one and fired it up. Worked like a charm and maybe this old stove will live on to make more Roast beef dinners.
If it been any easier my 10 year old grandson could have done it.

This repair took less than 5 minutes, literally! Two screws released the element, then unplugged it from two connectors. Then plugged in the new unit and screwed it into place. Cheap and easy!