Models > ARR6400LLP1143415NLL > Instructions

ARR6400LLP1143415NLL Amana Range - Instructions

Jump to:

All Instructions for the ARR6400LLP1143415NLL
46 - 60 of 186
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Tony from Rosendale, WI
Parts Used:
WP77001094
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Heating element on oven died
Removed two screws securing heating element. Removed broken element and disconnected wires. Removed back panel of oven, unplugged from outlet, installed new element, attaching 2 screws. From back side of oven reattached 2 wires, replaced back panel and plugged in. Pretty simple!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nancy from Baldwinsville, NY
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Burner would not heat up.
Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from centereach, NY
Parts Used:
WP77001094
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
bake element burnt out
had to slide the range out from the wall and pull the electrical plug, then using a nut driver ,I removed 9 screws from the back panel and removed the back panel to expose the bake element wiring, had to remove the three wires connecting the power cord to the range terminals a/c the back panel would not fully come off with these wires connected. i then pulled the 2 stake eyes from the element, unscrewed the 2 screws
securing the bake element from inside the stove and removed the element, re-installed the new element and screwed into place, attached the
stake eyes on the rear of the element and re-attached the power cord, put the back cover back on and plugged the range in., tested and the range functioned as intended.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lawrence from BROOKSVILLE, FL
Parts Used:
330031
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Screw hard to get off
Drilled a pilot hole with a 1/16 th drill bit and tapped off screw head.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Vidanand from Rochester, NY
Parts Used:
Y0309074
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Oven glass imploded during use.
Removed oven door by pulling off of hinges. Then removed screws that held door frame together. Replaced glass. Reassembled.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Denise from Pittsburgh, PA
Parts Used:
WP314763J
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Missing oven rack
Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Milford, MI
Parts Used:
330031
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
burner inop
removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roland from Stevens Point, WI
Parts Used:
WP77001094
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
baking element replacement
Very simple fix. I pulled the stove away from the wall and unplugged from outlet. Open the oven door and remove the oven racks. I used a phillips screw driver to remove the 2 screws holding the element and then pulled out. There were 2 wires attached to the element, those just pull off. Just reverse the process with the new element and you are good to go.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Julie from Salt Lake City, UT
Parts Used:
WPW10259865
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The heating element on the left front burner was out
Pulled the old one out and plugged the new one in. It was that simple!
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jason from Evanston, IL
Parts Used:
WP77001094
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven wouldn't heat up in bake mode but would heat up in broil mode.
Removed 2 screws from mounting plate in base element.

Disconnected 2 wires from bake element.

Installed new bake element in reverse.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Duxbury, MA
Parts Used:
WP77001094
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Old element caught on fire and split.
Switch off the breaker or unplug.
The screws were in tight so make sure your philips bite is new so you do not strip.
Pulled the element out and held the wires in place with a clothes pin so not to slip back in the stove.
Connect and cooked up pizza for dinner.
Very easy
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
dorothy from casco, ME
Parts Used:
WP77001094
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
burner caught on fire-arcing
Removed two screws-put burner in-pit screws back in! Turned over on and it worked!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Mapleton, UT
Parts Used:
8009, WP77001094
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
Oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and was about to disconnect the two wires. It was a bit hard to pull out the wires by hand, but I got some WD-40 and pliers and it was easy. Hooked up and replaced and voila. It was done. Saved me a new $1,500 stove. I wish I knew that the lamp only needed to be unscrewed and not the whole unit replaced.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerry from Mackay, ID
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
N/A
I followed the instructions provided.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sandra Collignon from SANTA CLAUS, IN
Parts Used:
WPW10196405
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Drip Pans were stained and burned on.
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ARR6400LLP1143415NLL
46 - 60 of 186