ARR6400LLP1143820NLL Amana Range - Instructions

Removed 2 screws from mounting plate in base element.

Disconnected 2 wires from bake element.

Installed new bake element in reverse.

Removed two screws-put burner in-pit screws back in! Turned over on and it worked!!!

Pulled the old one out and plugged the new one in. It was that simple!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and was about to disconnect the two wires. It was a bit hard to pull out the wires by hand, but I got some WD-40 and pliers and it was easy. Hooked up and replaced and voila. It was done. Saved me a new $1,500 stove. I wish I knew that the lamp only needed to be unscrewed and not the whole unit replaced.

I first killed the power to the oven by switching off the circuit breaker and then unplugging it from the wall. With the oven pulled out, I removed the back cover panel to disconnect the lower (bake) element power leads from the broken element. I removed the two screws on the metal plate that attached the element unit to the oven and removed the whole bake element assembly from the oven. I then inserted the new element assembly into the oven and reattached the screws. The next step was to reattach the power leads to the new element. It was then time to put the back cover panel back on and plug the oven back in. I then pushed the oven back into place and switched the circuit breaker back on. Finally, I tested the new element to see if it operated properly by setting a temperature and observed the temperature on a separate oven thermometer used for baking. Your exploded views of the oven helped me plan and execute this repair. Good feature that would be even better if the resolution was a bit better.

came only I had to order the set again

Switch off the breaker or unplug.
The screws were in tight so make sure your philips bite is new so you do not strip.
Pulled the element out and held the wires in place with a clothes pin so not to slip back in the stove.
Connect and cooked up pizza for dinner.
Very easy

I followed the instructions provided.

Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.

Removed screws on edges of door. Romove front panel. Remove several screws around glass. Replace inner glass and replace screws. A little tricky reinstalling trim around door front.

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!

Turn the power off to the Stove
Removed six screws from the Baffle Drip and removed Baffle Drip. Removed two screws from the Oven Light Assy. Position the Oven Light Assy to get to the ERC-3. Removed four screws from the ERC-3 unit and separated the ERC-3 unit from the Oven Light Assy. Remove the old Overlay, Mylar from the ERC-3 Unit. Install the New Overlay, Mylar on the ERC-3. Install the ERC-3 back to the Oven Light Assy. Install the Over Light Assy. Install the Baffle Drip and turn the power on to the Stove.

Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.