ARR630LLP1142627NLL Amana Range - Instructions

I turned off the breaker and unscrewed the element. Removed the plug connection and once I got the correct part, we plugged it in, screwed it back into the oven wall and done! I am a single female and was able to replace the heating element in a short amount of time with assistance from my 16 year old son!! I was very surprised at how easy it was to repair. The key is to get the correct part the 1st time!

First, I unplugged the power cord from the receptacle. I then removed two philiphead screws that hold the element in place. I the pulled the element out about an inch and a half . I then disconnected the the two wires from the element. The I connected the replacement element and resecured it with the two mounting screws. I assured everything was correct and then I plugged in the power cord and turned the oven on low heat to give it a test. Everything workout just great. The part was just what I needed.

I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.

removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair

Very simple fix. I pulled the stove away from the wall and unplugged from outlet. Open the oven door and remove the oven racks. I used a phillips screw driver to remove the 2 screws holding the element and then pulled out. There were 2 wires attached to the element, those just pull off. Just reverse the process with the new element and you are good to go.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

Removed oven door by pulling off of hinges. Then removed screws that held door frame together. Replaced glass. Reassembled.

I followed the instructions provided.

Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.

I first killed the power to the oven by switching off the circuit breaker and then unplugging it from the wall. With the oven pulled out, I removed the back cover panel to disconnect the lower (bake) element power leads from the broken element. I removed the two screws on the metal plate that attached the element unit to the oven and removed the whole bake element assembly from the oven. I then inserted the new element assembly into the oven and reattached the screws. The next step was to reattach the power leads to the new element. It was then time to put the back cover panel back on and plug the oven back in. I then pushed the oven back into place and switched the circuit breaker back on. Finally, I tested the new element to see if it operated properly by setting a temperature and observed the temperature on a separate oven thermometer used for baking. Your exploded views of the oven helped me plan and execute this repair. Good feature that would be even better if the resolution was a bit better.

No problem Took off old ones and replaced with new.

Switch off the breaker or unplug.
The screws were in tight so make sure your philips bite is new so you do not strip.
Pulled the element out and held the wires in place with a clothes pin so not to slip back in the stove.
Connect and cooked up pizza for dinner.
Very easy

Removed 2 screws from mounting plate in base element.

Disconnected 2 wires from bake element.

Installed new bake element in reverse.

Pulled the old one out and plugged the new one in. It was that simple!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and was about to disconnect the two wires. It was a bit hard to pull out the wires by hand, but I got some WD-40 and pliers and it was easy. Hooked up and replaced and voila. It was done. Saved me a new $1,500 stove. I wish I knew that the lamp only needed to be unscrewed and not the whole unit replaced.