AER5815RCW Amana Range - Instructions

Remove door
Remove front cover of door
Remove hinge screws
Put back together.

The part fit perfectly.Ther repair was logic. The door was of course heavy . I needed an extra hand.
I would have appreciated of instructions were included with the part. Also a web link on how to do it would alos have helped greatly

Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

after i recieved the parts with the glass still laying on the foam pads it was packed in i put some soap on the bottom so the new bracket would slide on easier. i centered the bottom bracket on the bottom of glass and pushed in place. i then picked up glass and slid it up in place on oven door attached the screws on bottom done

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

The first time is always the hardest. I took out the bottom cover that had 2 screws saw the broken element took out 3 screws to the emement. I then pulled out the stove unpluged it from the wall and took off the back panels several screws and found the element connected to the wires I marked the wires left & right and disconected them. I reversed proceedure to install the new element. The oven still won't go over 250 degrees I think when the element blew it to the circuit board with it.

ordered new broiler pan

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Unscrewed bottom piece; put on tape and new glass; re-installed bottom.

Can of Corn fix! Remove the two screws in the element cover plate (they're in the back- left/right corners). Remove the two screws that hold the element in place. Pull out the two prong ends of the plug in portion and hold the black / white leads so they do not fall back in behind the unit. Plug in new element (it only goes one way). Screw everything in and test. Place cover plate on after test. Like I said ... a "Can of Corn" fix!