ARG7300LL-P1143317NLL Amana Range - Instructions

Removed the oven racks for room to work.
Removed a protective cover (slide forward, lift up).
Remove winged cover plate.
See igniter assembly.
Remove 2 or 3 holding screws (I don't want to go in and count them - it's obvious - they are clearly in view - get a good screw-driver seating - they come out easily).
The igniter assembly is then loose and ready to com out.
Remove the stove drawer to get at the access plate at the rear - comes off easily(the wires to the igniter were then clearly identifiable).
Release the wire plug - I marked one side with a sharpy - polarity of fit, not voltage.
Gently feed the igniter assembly out the bottom using the wires.
Remove the igniter from the shroud (may have to pul it apart a little - it's tight - it does come out easily after prying the shroud a little - mark a side with a sharpy - for mechanical orientation.
The part number should be on the igniter.
I did not bother matching the part number.
Just matched the stove brand and model.
The parts diagram provided by PartSelect was invaluable.
I put an ac meter up the holes of the plug (stove side, of course) turned on the stove to see the meter measure 115vac - assurance that the igniter was bad and not anything else.
Just reverse the removal process.
Just takes a little time and patience.
Very very doable.
Good luck.

Replaced glow bar/ igniter.

Unplugged the stove, removed all 4 burner discs from the stove top (2 screws each- WATCH YOU DONT STRIP HEADS) and disconnecting electrode wires ( DONT HAVE TO- IF YOU HAVE ENOUGH ROOM TO SIDE TOP UNIT OVER), unscrewed the old module, removed each of the 6 wires,one at a time and connected wires to the new module. Plug in stove to test before you screwed it into place, reinstalled the top unit , put the stove top in place,. Done!

I removed the ignitor.
Ordered the matching part.
4 days later the part arrived and I installed the part.

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

remove knobs and 2 screws from front panel, remove front panel. remove burner grates and caps. remove 8 screws (2 per burner base). remove each base and unplug wire. remove the top of the range. locate an remove old ingition module with bracket. on my model i did not need the new bracket. the new module fit right in the old one. unplug wires from old module and plug them into the new one in the same place they were in the old one. reverse the order to reassemble. new module does not make the same clikcing noise (not as fast as old one), but it lights on the first click. GRERT JOB PARTSELECT.!!! parts go to my house within 2 days...saved about $40-$50.

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy repair,

Removed the three screws holding the igniter, pulled the old one out and plugged in the new one. Very simple.

Researched through this site to find part numbers and names. Youtubed it to see how to install the part. Ordered the exact part via this site and received it in only a day or two. Installed it in less than 15 minutes and the oven works amazing. It gets up to temp quickly and holds temp better than it has in years. Very satisfied!

ordered new broiler pan

I pulled the racks out of the oven. Then pull the plate off that covers the burner. There is another shield with a nut on it that covers the burner. Removed it.
The ignitor is mounted on the back of the burner, held by 3 screws, remove them. Pull the bottom sliding drawer out completely. (you have to lay down for this). There is a metal plate in the very back held with 2 screws, remove them and pull the plate out. You'll see the 2 high temp wires (White) with a plug connector, simply unplug the connector and you are ready to pull the whole ignitor assembly off the burner. The ignitor ceramic base simply slides out of the sleeve.
Put the new ignitor in the sleeve and put everything back together. It's pretty simple.
This is the second ignitor I have installed in 2 years, hopefully I'll get more life out of this one.
Good Luck.

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

Removed oven grills and top of burner pan. This exposed the igniter. Removed 3 phillips head screws from igniter bracket. Slid old igniter out the back end. Removed utility drawer. Removed two screws from back pan covering igniter plug-in. Unplugged igniter, removed from range. Handling of igniter is tricky..do not touch black end. Slide new igniter into the bracket, feed wire with connector through hole in back (where igniter was removed from), install the three screws for the bracket (your new igniter is now secure), from the bottom, plug in the new connector it only goes on one way. Re-install pan with two screws. Put utility drawer back in..job is complete!!

diagram on website was very helpful. simply unscrew two screws,remove and replace electrode and works perfectly.
Ordered one day arrived next with standard shipping installed before next day supper awesome service