AER6303MFB1 Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from The Villages, FL
- Parts Used:
- W11171119
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Electric burner element not working
Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ENID, OK
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from WHITE RIV JCT, VT
- Parts Used:
- WP3148952
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element temperature inconsistent
Turn off power to the stove (unplug or turn off breaker)
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
Remove back panel screws (Phillips) and back panel
Unplug switch
Remove knob and attaching screws (Phillips)
Remove and replace switch
Reinstall screws for switch and plugs in the back
Snap off the end of the stem if it's too long and reinstall knob
Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from MARGATE, FL
- Parts Used:
- WPW10310922
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
It break with the time
I order the part here, the first part never arrived, it was an empty package, the second part was breaking, the glass support was missing. Broken from the vent trim, then I was tired of it so I just put back the original broken part with some super glue on it, lol
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from FOUNTAIN INN, SC
- Parts Used:
- WP3148952
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cooktop on and cooktop hot indicator lights stayed on.
Range surface element control switch was bad. Replaced the switch and every thing works fine. Removed two Philips head screws in front and two Philips head screws in back of the range. Pulled the front panel away from the back of the range with the power off of course. Unplugged the wires and removed the two screws that held the switch in. Replaced the switch and refastened the control panel. Tested the switch and every thing worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from THE VILLAGES, FL
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner wouldn't regulate temperature
Turned off power to range. Took back panel off to reveal all controls. Pulled off knob of bad control. Removed 2 screws from the front of the control. Pulled off wiring from back of old control. Took new control reversed procedure. Reinstalled back panel turned power on and tested new control. Total time about 20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandeep from EDINA, MN
- Parts Used:
- W10777162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
screw came off
very expensive to buy the part but just tighten the screw intot eh predefined place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from APACHE JCT, AZ
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Elementwas burnt into
Watched the video and did as shown
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenny from GREENFIELD, IN
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Removing an heating element that burnt into .
Unplugged oven , removed screws ,pulled wires out, removed old element , just hooked wires up , screws .make sure it sits level plugged in. Works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from COON RAPIDS, MN
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from JACKSON, WY
- Parts Used:
- WPW10308477
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element non operational
removed two screws to faceplate at rear of oven. Disconntected contact wires, installed bake element reconnected contact wires, attached faceplate turned on oven holy hell it works just saved some money on service call thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Scranton, KS
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from BRIDGEBORO, GA
- Parts Used:
- WPW10181986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven temperature was 50 degrees off
Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from chipely, FL
- Parts Used:
- WP355214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door of oven came apart when plastic screw holders broke
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
Was this instruction helpful to you?
Thank you for voting!