ARGS7650LL (P1130765NLL) Amana Range - Instructions

this was the second one replaced in 5years,they don't make things like they used to

First I removed the two screws that hold the element in plance. I then pulled the element out about 3 in ches and disconnected the two wires

I listened to see if the stove was igniting. It was not so we went with the igniter. It arrived in three days. I thin watched a u-tube repair. It was very helpful but looked as if a few steps were unnecessary. After reading the responses decided what steps could be eliminated and carefully replaced the part. It worked the first time. Besides handling the ceramic part very carefully the hardest part was remembering what screws went where! Extremely glad I took this on as a first time stove repair.

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

remove cover bottom of oven slides out, remove three screws holding ignighter, problem i had was finding how to get to where the wire connects. there is a cover all the way in the back held by two screws this is found after removeing storage drawer on bottom.

1.) Trun Off Power
2.) Remove the Storage Drawer and the two (2) screws holding on the (Ignitor Plug) access cover-plate located in the back of the storage drawer access. (see page 15 if same model)
3.) Dissconnect the Ignitor Plug
4.) From the oven opening remove the three screws holding the Ignitor Holder.
5.) Remove the Ignitor and Holder from the oven by gently guiding the wires through the access hole
6.) Pull the Ignitor from the holder
7.) All Ignitors are extremelt fragile; install the new Ignitor into the Holder and make certain it is installed tight, mine was not. (Slight bending with my thumbs on the 1/4" flanges might hold it tighter if it is lose.)
8.)Reverse the process.
Note: One person here said they removed "ALL" the screws, maybe it was a different model, I only had to remove a total of "5" screws, two at the access cover plate and three at the Ignitor holder.
First time took me 20 minutes, if I needed to do it today, maybe 10.
Please also note that I didn't troubleshoot the Ignitor, as I didn't have a wrap-around amp meter, but the typical problem here would be the Ignitor, not the Gas Valve. Good Luck, pt

Removed racks and pans from oven, removed 1 screw that housed the v shaped burner cover. Then I noticed the Igniter housing was held to back of oven with 3 small screws, removed 3 screws, and noticed the igniter just slid into the housing, but the connection would not come through back of unit. pulled out the lower tray to expose the underside of the oven and noticed 2 screws holding a metal cover, removed those and noticed connection to igniter, undid the connection, slid out the igniter and then just reversed the process to put back. It took me about 20 minutes, and that was only because I was being overly careful with the ceramic igniter, as the one in there just crumbled. Very easy job for anyone with even moderate skills. Ordered my part with assitance from a lady at parts express on Monday at noon, had the part delivered Tuesday at 3:00, had the oven back up and running fine by 3:30. Couldn't be happier, as this happened once before and the repairman charged me $185, this cost $48 and 15 minutes.
Unbelievable service and detailed help. I have this site bookmarked for anything moving forward.
Thanks

Turn off power to unit. Remove one nut inside bottom of oven to expose glow bar and igniter. Take 3 screws off of ignitor cover and remove it.

Pull out pan storage drawer to expose igniter plug connector. Unplug connector. Remove igniter.

Plug in new igniter and reverse the above instructions to reassemble.

This was a much easier repair than I thought it would be. I read online that, given the problems my oven was having, it was almost certainly the igniter that was the problem. It was - with the new igniter it works perfectly!

Took cover off inside of oven to expose igniter - 1 nut! - igniter would not glow --3 screws to remove - pulled out storage drawer - un screwed oven shields - (2) - 6 screws - unplugged plastic igniter plug - an replaced! - simple - thank you and made wife buy me dinner for the probably $60 service call! --- thanks to those that posted before me to make this possible!

you need to remove the shield then the tray under the burner and burner tube.then you can get to the plug. Just remember when putint it back you need to put the burner tube in first then the tray then you can screw the element back in place. replace all the screws. works great.

I assumed it was the igniter. The trick is to remove the bottom storage drawer for access to where the igniter is connected. You then need to run the wire up into the oven and mount next to the gas.

My husband took it apart then showed me how to put it back together. So I placed it in the metal holder and attatched all the screws.

I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.

My husband did the repair. He removed the wires and screws from the element and replaced with new part.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Once I received the replacement part I simply reversed the process and it worked perfectly.