ARC700WW (P1142652NWW) Amana Range - Instructions

Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.

First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws for the cooktop.I put in the new burner & it worked just like new.

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

First I removed the one screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube over the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.

First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They work very well now.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I reconnected the wires to the new element and screwed it in to the oven back. Simple and inexpensive fix.

The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the connectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked!
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.

my wife did the the job and it was that easy. she took out two screws sliped the wires off put the two wires back on and put the screws in . She is a bank teller and teachers water aerobics

This repair took less than 5 minutes, literally! Two screws released the element, then unplugged it from two connectors. Then plugged in the new unit and screwed it into place. Cheap and easy!

We unscrewed the old element by removing 2 screws and put the new element in place and put the 2 screws back in and it was done. Piece of cake!

First, I turned off the power to the house at the breaker box. Then I removed the broken heating element through the front oven door. I hoped this would work as it seemed from other reviews that some people pulled the oven out removed the back panel in order to access the element. I unscrewed the plate and then gently pulled the element out. I had a little trouble "unplugging" the element. When I tried pulling, it seemed they were stuck tight. Turns out you have to sort of jiggle the connectors and then they easily pull apart. Had I figured this out initially, the repair would have been under 15 minutes. Attaching the new element to the connectors, rethreading the wiring back into the holes, and then rescrewing on the back plate too the oven wall took just minutes. Easy peasy. So glad I spent $40 to fix rather then $500+ for a new oven!

Pretty simple. Turned off breaker. Lifted the top, cut the 2 wires. Going to the burner, put the 2 wire nuts on, and screwed the bracket in.

Turned off 230 volt breaker to range,connected old wires to new element ,put back into place replaced the two mounting screws. Turned breaker back on and tested range.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new wires, replaced the two screws and turned on the oven to test it. Easiest repair job I have ever done.