ARG7300W-P1143320NW Amana Range - Instructions

i read other stories and found after checking rotating heat switch with ohm meter found the igniter was the problem, pulled up on door and it came off, found bottom of oven pulled up and out, removed wing nut from deflector and two bolts and one wiring connector, just reversed removal to install new igniter and all complete, took about 20 minutes,

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Removed oven door. Removed three screws on ignitor holding bracket. Pulled out the range from the wall and reached underneath to access the wire nuts on the wires. Removed old ignitor and replaced with new one. Reconnected wires and then and replaced bracket and that's it. Works great now.

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

Replaced the existing ignitor by removing the bottom drip pan/gas line/ignitor (apprimately 18 screws), unscrewing the wire nuts, removing the old ignitor, connecting the wires to the new ignitor, and reinstalling the drip pan/gas line/ignitor (18 screws).

My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.

I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.

For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

Part Select was a great site for diagnosing the problem and providing the schematics of the range.
The part arrived quickly. All we had to do is pull off the old knob and replace it with new knob by pushing it on the rod that connects and controls the thermostat.

The directions offered by others here were spot-on. I had never done any repairs on any ovens before, and this took about twenty minutes for me.

Slide out the oven racks. Slide out the pan at the bottom of the oven. Use a wrench to remove the nut in the center of the heat diverter. Unscrew three screws holding the igniter housing to the back and gas pipe. Pull the old igniter forward just a little. Remove the igniter housing from the old igniter and CAREFULLY put it on the new igniter; do not touch or break the new igniter.

Remove the drawer. Unscrew the two screws holding the shield up near the back of the oven (it's not as far or hard as it first sounds). Back inside the oven, thread wiring for the new igniter into the hole in the back. Down under, unplug the old igniter (green plug) and plug in the new one. Pull the old igniter completely out of the oven.

Replace the shield underneath. Push the remaining new igniter wiring into the hole as you replace the igniter housing with the new igniter back in place. Replace the three screws. Turn the oven on briefly to test ignition before putting the rest back together.

If all is well, replace the heat diverter and the nut holding it in place. Replace the bottom pan, oven racks, and drawer.

Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC

Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter

Removed old ignightor and installed new one