ARG7102C-P1143389NC Amana Range - Instructions

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

Took the pan out of the bottom of the oven. Took the screws out of the assembly for the iron, disconnect the power wires under the stove and pull out the old iron. Reverse the proceedure but be careful with the new iron, it is very fragile. Connect the wires put the screws back and you are done. Make sure before you start the job that you unplug the appliance !!!!

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

1. Remove sliding shelves and lower pan sheild
2. Remove flame deflector
3 . Remove the 3 screws that hold the igniter in place. Insert the new cable and plug through the opening for connection in step 6. You may hve access to connector. If so skip to step 8.
4. Remove sliding storage drawer
5. Remove the sheetmetal pan to gain access to the igniter connector. It might help to have several blocks of wood the elevate the frront of the stove to allow more working clearance.
6. Disconnect old igniter, connect new igniter.
7. Replace pan and sliding drawer.
8. Remove old igniter from carrier and install new one.
9. Install igniter carrier to stove with 3 screws
10. Replace flame deflector and lower pan sheild.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

remove cover bottom of oven slides out, remove three screws holding ignighter, problem i had was finding how to get to where the wire connects. there is a cover all the way in the back held by two screws this is found after removeing storage drawer on bottom.

First I removed the two screws that hold the element in plance. I then pulled the element out about 3 in ches and disconnected the two wires

Identifing what part to replace was the most challenging task. So, what I did to trouble shoot what was broken and identify the specific compent was the following. I was not sure that the igniter was broken becuase it illuminated rather bright but the oven would not turn on. The broiler on the other hand worked fine so I removed the igniter from the broiler and placed it in place (the igneiter is a different size) of the oven igniter and guess what the burner cut on...So I ordered the oven igniter and everything worked fine.

The repair actually started online trying to figure out the problem. The parts list and picture provided were a big help. I actually got lucky when I ordered the part. It was a little difficult to get to but once I got the old one out, it was easy and done quick. Saving at least $100 on a repair man was awesome. I had to find the part in the stove first. Then had to find the wiring harness to disconnect. After taking off the back panel and the oven burner plate, the wire harness was exposed. I disconnected, taped on the new wires, remounted the new igniter and put it all back together. Pretty quick and pretty easy.

1. Disconnect oven electric supply.
2. Remove oven door (2 screws).
3. Remove inside-oven bottom plate (slide forward, lift).
4. Remove inside-oven burner cover (1 nut).
5. Disconnect igniter enclosure (3 screws).
6. Remove under-oven drawer (slides out).
7. Remove panel at back of oven in under-oven compartment to access igniter electrical connection (2 screws).
8. Disconnect old igniter.
9. Extract old igniter from igniter enclosure. (Don't use much force; just slightly expand the metal flanges of the enclosure.)
10. Dispose of old (bad) igniter.
11. Insert new igniter into igniter enclosure.
12. Place igniter enclosure in oven compartment and slide electrical connector through to back/lower compartment.
13. Connect new igniter in under-oven compartment.
14. Replace panel at back of oven in under-oven compartment (2 screws).
15. Replace igniter enclosure (3 screws).
16. Replace inside-oven burner cover (1 nut).
17. Replace inside-oven lower plate.
18. Replace oven door (1 screws).
19. Reconnect electric supply.

this was the second one replaced in 5years,they don't make things like they used to

It took me a while to figure out how to access the igniter (I ended up removing the drawer and had to slide underneath the oven.) Once I removed the two sheet metal panels, I unplugged the old igniter and plugged in the new one. Installing the igniter inside the oven was easy--three sheet metal screws that hold the protective cover.

All I would like to say is that I am very satisfied with the service I received from PartSelect.

I definitely would order from them again. By doing the work myself, I believe I saved $80 in labor costs.

Thank you

The oven door had a stripped thread so I took a knife and held up on washer and unscrewed it. I unplugged the oven. Then slide door off. Then removed pan in oven, then used socket wrench to take off burner sheild (reflector). Then You take out bottom drawer, in the back of opening there is a cover over the connections 2 screws. I unpluged the igniter. Now back in oven the igniter has a cage with 3 screws.. the screw was rusted and frozen. Needed to use WD40 on the screw and let set 10 mins. Now I could remove that screw and other 2 screws. With the cage off I was able to go to bottom where the drawer was and reach in and pull igniter completely out. Becareful not to break the anode it is fragle. ( the black piece) Then reverse and put the new one in. I actually swaped some of the rusty screws that gave me trouble with other screws in the oven that were the same, in case I have to do this again some time in the future. These previous comments from people were greatfully helpful!!!! Thank you!!!