ARG7102W-P1143389NW Amana Range - Instructions

First, i removed all of the oven parts that needed to come out in order for me to remove the ignitor. Second, removed the manifold and the old oven ignitor. Then, i checked for 120 volts going to the ignitor. Replaced the ignitor with the new one and reassembled all of my oven parts. 15 mins top, but of course it may take a little longer for those of you who are not elecrically and mechanically inclined. Very east to repair.

I first diagnosed the problem with an ammeter, after I was sure of the problem I ordered the part and it came in 1 day early. When the part arrived I removed 12 screws to access the old part, unplugged it, plugged in the new one. The easiest way to save $150.00 I've managed.

Thanks to previous reviews it was really easy! Popped cover plate off bottom of oven. Removed diffuser plate by using socket wrench to remove one bolt. Removed three screws (one on top; two on left side) of bracket. Good idea to use a magnetic screwdriver so they don't get lost! Slid igniter out of bracket- a bit tricky but gently eased it out. Slid new igniter in place taking care not to touch the element. Dropped wires and harness down next to old ones. Removed bottom drawer, crawled under and switched connections. Put everything back together. It did take a little longer for the new igniter to start the first time- about one minute- but now fires right up.

Part arrive only a couple of days after ordering, and installation time was less than to schedule a repairman! My only regret is that I didn't send my better half off for the entire afternoon so I could really make it out to be a big deal as my brother-in-law, the appliance repairman, made it out to be!

First, I took out the racks from the oven. Next, I took out the black small square cover off the bottom of the stove, which gave me access to the oven ignitor. Then, I removed the screws to be able to take out the ignitor. Finally, I took the bottom drawer out to access the ignitor wire. I pulled the plastic connectors to disconnect the wire. I took the ignitor out and replaced with the new one. I put everything back in reverse order. The oven warmed up about 2 minutes after I turned it on.

Pulled the burner cover, removed two screws holding igniter in place, pulled oven out from wall and unplugged igniter at back, feed wire and plug back thru to oven. Removed old igniter from holder slid new one in place and reversed procedure to feed wires back thru to back side. Plugged in igniter replaced burner cover and pushed stove back into place. The procedure took about five minutes if that.

After removing the oven shelves, the burner cover came right up. The ignitor was in plain sight, and after removing the screws I pulled it straight out so I could get to the wire nuts. After swapping out the old igniter and sliding the cover over the new ignitor, the new piece slipped back into place in the oven. The screws were put back in, and the burner cover and shelves put back, and the oven works wonderfully again.

Ordered new ignitor and recieved it in two days. Took out broiler drawer, took out 6 screws ,replaced ignitor reinstalled screws and broiler drawer in less then 15 minutes. New ignitor works perfectly. Couldn't of been any easier.

I identified the igniter problem in the lower part of the oven by turning the upper broiler on and finding that it worked. I then knew it was not a gas supply problem. Replacing the igniter required removing the two oven racks, removing the drip pan, removing two screws that connect the igniter to its mount and disconnecting the wires in the back of the oven. The install was the reverse of removal. One tip, on my oven I was able to lift the oven door off of its hinges which allowed much easier access to the igniter.

basicly just replaced the element by unplugging the connector and removing the three screw that hold the element. easy process.

Thanks to this website I was able to quickly identify the needed part. A few days later I had it. To install the new part I had to open up the bottom inside of the oven to access the igniter assembly and remove the drawer to get to the connecting plug underneath. Four screws needed to be removed, unplugged the old part and plugged in the new part. Replaced the four screws to hold the igniter in place. Replaced the drawer and fired it up. Worked great!

you need to remove the shield then the tray under the burner and burner tube.then you can get to the plug. Just remember when putint it back you need to put the burner tube in first then the tray then you can screw the element back in place. replace all the screws. works great.

I assumed it was the igniter. The trick is to remove the bottom storage drawer for access to where the igniter is connected. You then need to run the wire up into the oven and mount next to the gas.

Took cover off inside of oven to expose igniter - 1 nut! - igniter would not glow --3 screws to remove - pulled out storage drawer - un screwed oven shields - (2) - 6 screws - unplugged plastic igniter plug - an replaced! - simple - thank you and made wife buy me dinner for the probably $60 service call! --- thanks to those that posted before me to make this possible!

Turn off power to unit. Remove one nut inside bottom of oven to expose glow bar and igniter. Take 3 screws off of ignitor cover and remove it.

Pull out pan storage drawer to expose igniter plug connector. Unplug connector. Remove igniter.

Plug in new igniter and reverse the above instructions to reassemble.

This was a much easier repair than I thought it would be. I read online that, given the problems my oven was having, it was almost certainly the igniter that was the problem. It was - with the new igniter it works perfectly!

My husband took it apart then showed me how to put it back together. So I placed it in the metal holder and attatched all the screws.