ARG7102L-P1143389NL Amana Range - Instructions

Removed burner with attached igniter assembly by raising forward legs from slots and pulling unit from rear support. Note: this is contrary to instruction #1 on installation instructions. Then followed the remaining instuctions 2 - 7 as written. Everything worked as planned.

1. Removed racks
2. Removed bottom cover
3. Removed screws holding ignitor
4. Removed storage draw
5. Removed cover over wires
6. Unplugged ignitor & placed with new
7. Put back together

1. Remove sliding shelves and lower pan sheild
2. Remove flame deflector
3 . Remove the 3 screws that hold the igniter in place. Insert the new cable and plug through the opening for connection in step 6. You may hve access to connector. If so skip to step 8.
4. Remove sliding storage drawer
5. Remove the sheetmetal pan to gain access to the igniter connector. It might help to have several blocks of wood the elevate the frront of the stove to allow more working clearance.
6. Disconnect old igniter, connect new igniter.
7. Replace pan and sliding drawer.
8. Remove old igniter from carrier and install new one.
9. Install igniter carrier to stove with 3 screws
10. Replace flame deflector and lower pan sheild.

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

remove cover bottom of oven slides out, remove three screws holding ignighter, problem i had was finding how to get to where the wire connects. there is a cover all the way in the back held by two screws this is found after removeing storage drawer on bottom.

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

Identifing what part to replace was the most challenging task. So, what I did to trouble shoot what was broken and identify the specific compent was the following. I was not sure that the igniter was broken becuase it illuminated rather bright but the oven would not turn on. The broiler on the other hand worked fine so I removed the igniter from the broiler and placed it in place (the igneiter is a different size) of the oven igniter and guess what the burner cut on...So I ordered the oven igniter and everything worked fine.

this was the second one replaced in 5years,they don't make things like they used to

I listened to see if the stove was igniting. It was not so we went with the igniter. It arrived in three days. I thin watched a u-tube repair. It was very helpful but looked as if a few steps were unnecessary. After reading the responses decided what steps could be eliminated and carefully replaced the part. It worked the first time. Besides handling the ceramic part very carefully the hardest part was remembering what screws went where! Extremely glad I took this on as a first time stove repair.

Replaced the igniter. With the new igniter, the gas came on when the oven was turned on and lit with no problem.

Thanks to this website I was able to quickly identify the needed part. A few days later I had it. To install the new part I had to open up the bottom inside of the oven to access the igniter assembly and remove the drawer to get to the connecting plug underneath. Four screws needed to be removed, unplugged the old part and plugged in the new part. Replaced the four screws to hold the igniter in place. Replaced the drawer and fired it up. Worked great!

you need to remove the shield then the tray under the burner and burner tube.then you can get to the plug. Just remember when putint it back you need to put the burner tube in first then the tray then you can screw the element back in place. replace all the screws. works great.

I assumed it was the igniter. The trick is to remove the bottom storage drawer for access to where the igniter is connected. You then need to run the wire up into the oven and mount next to the gas.

Took cover off inside of oven to expose igniter - 1 nut! - igniter would not glow --3 screws to remove - pulled out storage drawer - un screwed oven shields - (2) - 6 screws - unplugged plastic igniter plug - an replaced! - simple - thank you and made wife buy me dinner for the probably $60 service call! --- thanks to those that posted before me to make this possible!