ARG7800E-P1143355NE Amana Range - Instructions

First, I removed the oven door (two screws and pulled it off the hinges) and placed it out of the way. Then I removed the baking racks and bottom cover over the heating element this exposed the heating element, easily removed (two screws). I unplugged the old element, plugged the new element in, and put all the stuff back and the put the door back on. Next was the fun part. . . Had to get the wife to turn on the oven (very complicated touch pad - not made for a man to understand), and shazamm the oven came on! Now I can have some of those great homemade biscuits again!

Replaced glow bar/ igniter.

found igniter not working, pulled up on door and it came off, lifted up bottom of oven and pulled out, removed wing nut on deflector to access igniter, removed igniter retaining bolts, unplugged connector, be careful not to let connector slip back in stove, and reverse process to install new igniter,, all took about twenty minutes, easy repair,

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

I removed the ignitor.
Ordered the matching part.
4 days later the part arrived and I installed the part.

1. Removed racks
2. Removed bottom cover
3. Removed screws holding ignitor
4. Removed storage draw
5. Removed cover over wires
6. Unplugged ignitor & placed with new
7. Put back together

Removed the three screws holding the igniter, pulled the old one out and plugged in the new one. Very simple.

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

I pulled the ckt breaker, removed the oven drawer and disconnected the igniter. I opened the oven door and unscrewed the igniter holding bracket and removed the bracket and igniter. I broke the old igniter element when removing it from the bracket. When installing the new igniter in the holding bracket I broke the ceramic element. REALLY BE CAREFUL. Ordered a new igniter, very carefully installed it in the bracket, then rversed the removal process. It's not hard, you just have to be careful

Removed oven grills and top of burner pan. This exposed the igniter. Removed 3 phillips head screws from igniter bracket. Slid old igniter out the back end. Removed utility drawer. Removed two screws from back pan covering igniter plug-in. Unplugged igniter, removed from range. Handling of igniter is tricky..do not touch black end. Slide new igniter into the bracket, feed wire with connector through hole in back (where igniter was removed from), install the three screws for the bracket (your new igniter is now secure), from the bottom, plug in the new connector it only goes on one way. Re-install pan with two screws. Put utility drawer back in..job is complete!!

ordered new broiler pan

I pulled the racks out of the oven. Then pull the plate off that covers the burner. There is another shield with a nut on it that covers the burner. Removed it.
The ignitor is mounted on the back of the burner, held by 3 screws, remove them. Pull the bottom sliding drawer out completely. (you have to lay down for this). There is a metal plate in the very back held with 2 screws, remove them and pull the plate out. You'll see the 2 high temp wires (White) with a plug connector, simply unplug the connector and you are ready to pull the whole ignitor assembly off the burner. The ignitor ceramic base simply slides out of the sleeve.
Put the new ignitor in the sleeve and put everything back together. It's pretty simple.
This is the second ignitor I have installed in 2 years, hopefully I'll get more life out of this one.
Good Luck.

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

The repair was fairly straightforward. The drawer below the oven had to be pulled out and the panel in the rear (looking from the front through the opening where the drawer was) was removed. It was then a matter of removing two screws and unsnapping the wire connection. And then replacing the igniter.