AGDS902E-P1131833NE Amana Range - Instructions

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predrilled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

I went online to learn what F-3 meant and it said temp sensor malfunction. I ordered the part - it looked the same so I repaced the old one and then the plugs were different. I cut the plug off the old sensor and cobbled together a connection. I powered up the stove and the burners were ok, but the oven appeared dead. about an hour later the alarm went off and it displayed F-1. I figured I needed to order another part, but hit Oven cancel and the display lighted up. I set the clock, heated to 400 and made a tray of cornbread. It seems to work ok, but I need to make a better arrangement. perhaps cut the new part connector off and splice the old connector. I don't like having electrical tape so close to the oven - it will probably melt with much usage. It is working - for now!

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.

After removing the oven shelves, the burner cover came right up. The ignitor was in plain sight, and after removing the screws I pulled it straight out so I could get to the wire nuts. After swapping out the old igniter and sliding the cover over the new ignitor, the new piece slipped back into place in the oven. The screws were put back in, and the burner cover and shelves put back, and the oven works wonderfully again.

unscrewed the bracket holding the igniter in place then we pulled the drawer on the bottom out and disconnected the Igniter - then we took the unit out of the bracket replaced it and then put the bracket back into place screwed it in and reconnected the igniter and now it burns hotter then it has since we moved into the house two years ago.
I was worried that it would be a hard long job but was pleasantly surprised when it only took a few minutes.

I researched the needed part (igniter)and purchased it on line. It arrived promoptly. I called a repair person who arrived and installed the new part. All is well.

Removed old igniter held by one bolt & nut, diconected two leads to igniter. Gas mainifold remained in place during repair. Replaced with new igniter, using old mounting bracket and wire ties. Total repair time 30min, oven repair service wanted to charge $80 just for diagnosis. Total cost of repair doing it myself was $50.

First I turned off the gas supply to the oven and disconnected it. I then pull the oven out away from the wall. I then unplugged the power cord. I removed the oven door by lifting it off of it spring hinges. I then removed a lower plate that covers the burner element by pressing in a manner that it popped off. I then located the ignitor and removed 3 screws. All were easily removed. Carefully, I pulled the igniter out and removed the wires from the wires that supplied the current to the ignitor. Installation followed by working the steps above in reverse order.

Took off oven door, took out racks and bottom plate, removed burner assembly disconnected wires, removed old ignitor put new one in holder, connected wires, put burner assembly back, checked if it worked and replaced racks ect..No tools needed.

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

We unplugged the stove and turned off the gas. We slid the oven door off just to make it easier. Unscrewed 3 screws holding the igniter in place. Pulled the igniter out from the back of the stove. Disconnected the two wires. Slid the new igniter in the holder. Rewired it and slid it back into place. Put the screws back in and it was done. Plugged it back in, turned the gas on, tried it out and presto! It was perfect! Lit immediately and strong and now i have a brand new 20 year old stove. lol Happy girl! And this was done by 2 50 year old women!

The first igniter was received broken. A replacement was received within 5 days. It was very easy to install once the protective cover was placed over the igniter end. In my opinion, this part should be sold with the protective cover already in place.

Removed the old sensor which is held into the upper right of the back of the oven by removing the two screws and pulling the sensor out. Then disconnected the sensor from its connector. Replace the old with the new by simply clicking it into the connector. Then pushed the wire back into the oven wall and screwed the two screws back in. The whole job took about one minute to do after evaluating the process. While it was not necessary to remove the door, I did (which was very easy) and ended up cleaning the glass inside and out. All in all, a complete success. Oven working as new.