AGR4433XDS0 Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from carol stream, IL
- Parts Used:
- WP3405184
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
over-all different problems with esate.
Very easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from WALDORF, MD
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven wasn't preheating to temperature
Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BURNSVILLE, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Temp inaccurate
I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!
This was an easy fix for a seventy year-old like me!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SAINT CLOUD, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven sensor was not regulating heat set for oven
Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patrick from HUGHESTOWN, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
temp sensor went oven not heating
the hardest part was moving stove to trplace part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PLUM CITY, WI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven not keeping correct temp and sometimes would not relight when temp went dropped.t
Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mace Matthew from Canaan, NY
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The Igniter seized and the oven would not heat up..the gas would not light.
So....the oven stopped working.
I called a local appliance guy and set up an appointment to repair.
$90 to travel here.
$50 for the part
$ labor was about $75
..then tax.
BUT then....I had a moment of clarity.
A new Oven/Range/Stove top was about $400.
This guy was over $200 to repair a 4-7 yr old stove.
So I ordered the part.
A resus monkey could have fixed the stove...I really mean it...Easy is an under-statement.
I found a tutorial on you tube (how to change an Igniter.
Literally 6 screws and unplug the igniter and install the new igniter.
Replace the screws and replug in the unit.
and that's that.
I called a local appliance guy and set up an appointment to repair.
$90 to travel here.
$50 for the part
$ labor was about $75
..then tax.
BUT then....I had a moment of clarity.
A new Oven/Range/Stove top was about $400.
This guy was over $200 to repair a 4-7 yr old stove.
So I ordered the part.
A resus monkey could have fixed the stove...I really mean it...Easy is an under-statement.
I found a tutorial on you tube (how to change an Igniter.
Literally 6 screws and unplug the igniter and install the new igniter.
Replace the screws and replug in the unit.
and that's that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from HOUSTON, TX
- Parts Used:
- W10918546
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ignighter would not light and started smelling natural gas
Igniter is in the back bottom of the oven. I had to take off the top of the broiler compartment which has 3 screws. Unplugged the igniter which has two small screws and used a magnetic nut driver. installed the new one. It took 30-45 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gervice from BROUSSARD, LA
- Parts Used:
- WPW10209656
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Two of four gas surface burners would not ignite.
Replace two igniters that were not working. Did not fix the problem. Swapped wire positions from Spark Module and noted that the problem followed the igniter positions. Replaced Spark Module. Problem solved. Procedure required disconnecting a/c power, removing four screws, removing igniter wires from old module and reconnecting them to new module. Reinstalled new Spark Module in range. Reconnected a/c power. Test successful. Total time: 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from PRINEVILLE, OR
- Parts Used:
- W10918546
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Wrong part. The connection doesn't match.
Unscrewed the feet from the floor. Pried up the range top, removed burners. Unscrewed sides of the range from wooden cabinet it was recessed into. Unplugged range from outlet. Pulled range out into the open. Removed back cover. Discovered that I have the wrong replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George E from OCALA, FL
- Parts Used:
- 3184020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
the fastener became loose and dropped into the stove
This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark
George Clark
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandy from WILLCOX, AZ
- Parts Used:
- W10918546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven would not light
I took apart the bottom of the oven to see the ignighter. I moved the oven away from the wall and took off the metal plate that covers the ignighter electrical connection.Unplug the old part and plug in the new one. With the nutdriver remove the two screws holding the part onto the gas tube. Save the screws and attach the new part with them. Turn on the oven to see if the gas tube lights. If all is good put the metal plate on the back of the oven and replace the other oven parts. Make biscuits!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from MORRISTOWN, IN
- Parts Used:
- W10918546
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
oven igniter quit working
pulled the stove out removed back cover, unplug then unscrew igniter. Mounted new igniter in place, plug it back in , put cover back on, put stove back in place. Took about 20 min. Very easy repair, thank you.
Was this instruction helpful to you?
Thank you for voting!