AGR5844VDB5 Amana Range - Instructions

Snapped in the new drawer glide. Took less than 5 minutes.

Pulled shelves out removed bottom plate of oven remove heat shield cover removed screws had to remove bottom drawer disconnect wire from bottom of igniter and remove from top side . Replaced by reversing steps.

Removed door per instructions in manual. Removed racks and storage drawer per manual. Removed two phillips head screws holding bottom pan and removed pan. Removed two phillips head screws holding igniter tube (#12) and withdrew tube from the cavity. Removed two phillips head screws holding igniter and bracket to the tube. Unplugged elcetrical connection to igniter and installed new igniter in reverse order. Too bad the igniter wasn't the problem.

We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.

Clean off all broken glass and wipe down the debree,figure what side the glass goes then unscewed the base then the sides then add gorrilla glue on the edges to help set the glass in place had some hold it the screw th center bottom in first then got the sides in place with the bottom rack then screw it all back in to place making sure the side and top were in place right that was it.

The first thing you need to do is remove the racks from your oven.

Then look around at the back of your oven for the screws that hold the bottom pan down.

Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.

Remove the heat shield that is over the burner.

Remove the bottom drawer of your oven.

Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.

Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.

The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.

Once you have the old igniter out then you can carefully install the new one.

Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.

Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.

The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Replaced grates

Open oven door and remove racks. Remove 2 screws at back of oven floor and remove bottom plate. Unscrew screws that hold flame defuser. Remove defuser. Remove screws that hold bake igniter and flame tube. Unplug wire to bake igniter. Remove screws to bake igniter. Replace old igniter with new igniter. Replace screws and wire to igniter. Replace flame defuser and put screws back. Put bottom plate back into oven. Replace 2 screws at back. Replace racks. close door and test by setting thermostat to some temperature and verify that oven works.