AGR6303MFS0 Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Caddo Mills, TX
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inside Light would not work
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from chipely, FL
- Parts Used:
- WP355214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door of oven came apart when plastic screw holders broke
put back together with parts ordered. Parts arrived in 2 days!!!! and saved my large dinner party the following day from being ruined. Thank you so much for your parts inventory and for Jenn Air supplying only the part needed and not the entire door. It was a life saver!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
The Parts Came With No Instructions And We Couldn't Find Directions On Line.
We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Arlington, VA
- Parts Used:
- WP9758079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven has not heat
Open oven door and remove racks. Remove 2 screws at back of oven floor and remove bottom plate. Unscrew screws that hold flame defuser. Remove defuser. Remove screws that hold bake igniter and flame tube. Unplug wire to bake igniter. Remove screws to bake igniter. Replace old igniter with new igniter. Replace screws and wire to igniter. Replace flame defuser and put screws back. Put bottom plate back into oven. Replace 2 screws at back. Replace racks. close door and test by setting thermostat to some temperature and verify that oven works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Woodbridge, VA
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Ignater would ignate the first time, but then after the oven went off the ignater would not re-ignate and the ove would rmain off
The first thing you need to do is remove the racks from your oven.
Then look around at the back of your oven for the screws that hold the bottom pan down.
Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.
Remove the heat shield that is over the burner.
Remove the bottom drawer of your oven.
Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.
Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.
The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.
Once you have the old igniter out then you can carefully install the new one.
Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.
Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.
Then look around at the back of your oven for the screws that hold the bottom pan down.
Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.
Remove the heat shield that is over the burner.
Remove the bottom drawer of your oven.
Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.
Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.
The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.
Once you have the old igniter out then you can carefully install the new one.
Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.
Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Maple Valley, WA
- Parts Used:
- WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Trim piece on the botom of the oven was chipped in three places
I used the allen wrenches to block the hinges, removed the oven door and used the kitchen counter for a work station. I removed the trim piece at the bottom which released the side trim and oven glass front, and then reversed the procedure. It took more time to clean things than to do the exchange. My only issue is with Fed Ex who delived the first trim piece bent in the middle inside a crushed box. Part Select had another part sent the same day after I called them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from parkville, MD
- Parts Used:
- WP9758079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
oven would not light (heat up)
oven would not light but broiler and range top would. removed oven racks. removed 2 finger tight screws on oven pan floor and pulled up oven floor. also removed storage drawer under oven- also 2 screws. now your oven should look like the inside of your gas grill. removed 2 more screws on burner plate and removed plate. unplugged igniter and 2 screws holding igniter. replaced igniter and put together in reverse order. oven now works perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carl from peoria, IL
- Parts Used:
- WP9758079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Igniter went out
Pulled shelves out removed bottom plate of oven remove heat shield cover removed screws had to remove bottom drawer disconnect wire from bottom of igniter and remove from top side . Replaced by reversing steps.
Was this instruction helpful to you?
Thank you for voting!