AGS760L-P1141251NL Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Peter from Eagan, MN
- Parts Used:
- 32020101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 burners not igniting
Removed the burners 2 screws per burner disconnected the wires to the burners. Lifted the oven top off removed original ignition module. Installed wires to the new module taking note of replacement location. Than mounted new ignition module. Tha only hiccup was dropping 1 screw down into the stove lining found replacement screw and installed module. Cleaned and replaced top. Mounted burners and the stove is working like new. Project proved to be quite simple and guick. Thanks to partselect for there prompt delivery and other peoples input on install made it quite easy and simple,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Westlake, OH
- Parts Used:
- R0706011
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door wouldnt shut evenly.
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blaise from Deer Park, TX
- Parts Used:
- 32020101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Burners would not light everytime they were used.
I used the instructions that were online at the PartSelect website. Perfect instructions. It took longer to clean the unit than installing the new paart.The instructions that came with the part were not that useful.Thanks to PartSelect, my wife is now happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VICTOR from MOUNT PROSPECT, IL
- Parts Used:
- 786324
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable), Wrench set
Screws Were Rust6Ed, Melted
Used grinder to cut the screws. All 4 screws had to be cut to remove from burner assembly. Once this was acomplised it went fast with no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Milwaukee, WI
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stove sometimes would not light or took really long and did not maintain heat
We unplugged the stove and turned off the gas. We slid the oven door off just to make it easier. Unscrewed 3 screws holding the igniter in place. Pulled the igniter out from the back of the stove. Disconnected the two wires. Slid the new igniter in the holder. Rewired it and slid it back into place. Put the screws back in and it was done. Plugged it back in, turned the gas on, tried it out and presto! It was perfect! Lit immediately and strong and now i have a brand new 20 year old stove. lol Happy girl! And this was done by 2 50 year old women!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from UKIAH, CA
- Parts Used:
- 786324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven would not light.
Removed old igniter and replaced with new one.Tested oven and it went on. You need a phillips screwdriver to remove two screws and a small socket for the third screw to remove the igniter cage. Then pull out the wires from under the oven and disconnect. Reverse procedure to install new igniter. Reuse original connectors. Be very careful with the igniter because the tip is very fragile and can break easily.
Was this instruction helpful to you?
Thank you for voting!
Spark arcing was occuring at several spots along the length of the wire, th burners would sometimes lite on there own but as time went by i had to use a match to light the burners more and more till finally they would not lite by the spark ,which was getting weaker, or their would be little or no sp
after checking on line using model number and calling parts select ,the spark module was found to be defective, placed my order with them and at a very reasonable price replacedthe wires and module, very simple repair ,unplugging the range first I simlply removed the top by removing the two screws on each burner ,lifting off the top after disconnecting the wires from the burners ,carefule not to break the ends of the wires off and mixing them up, I simpley on screwed the module and removed each wire seperatly and replaced them one by one on the new module replaced the module on the range, hooked the wires up and presto done screwed downed the burners ,gas range works great thank you parts select for your parts and help,you saved me a bundle of money
Was this instruction helpful to you?
Thank you for voting!