AGR6011VDB0 Amana Range - Instructions

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Lifted the top disconnected the old valve and replaced with a new one.I believe the valve should have been shipped with two gaskets,. One for the bottom and another for the top. I reused the old one on the top with no problem but would have preferred a new one.

I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.

all I did was replace the igniter and that fixed my problem simple to do.

Removed old trim kit and handle installed new parts but was having problems with glass fitting between handle and bottom bracket there was a gap between glass and handle when installed fist time after disassembling again I found that the door frame it self had to be tapped back into alignment to be square but once the adjustments were made the installation was a breeze

The bake part of the oven was not igniting all the time . I checked the website and they don't list the igniter separately from the burner tube. This part is the exact fit for the igniter. There is no need to buy the whole kit if the igniter is all you need. it will fit right on the burner tube with no modification at all. Part number PS897264 is the igniter and burner tube. Part number PS898618 is just the ignitor.

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great

Pulled shelves out removed bottom plate of oven remove heat shield cover removed screws had to remove bottom drawer disconnect wire from bottom of igniter and remove from top side . Replaced by reversing steps.

We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.

Removed door per instructions in manual. Removed racks and storage drawer per manual. Removed two phillips head screws holding bottom pan and removed pan. Removed two phillips head screws holding igniter tube (#12) and withdrew tube from the cavity. Removed two phillips head screws holding igniter and bracket to the tube. Unplugged elcetrical connection to igniter and installed new igniter in reverse order. Too bad the igniter wasn't the problem.

oven would not light but broiler and range top would. removed oven racks. removed 2 finger tight screws on oven pan floor and pulled up oven floor. also removed storage drawer under oven- also 2 screws. now your oven should look like the inside of your gas grill. removed 2 more screws on burner plate and removed plate. unplugged igniter and 2 screws holding igniter. replaced igniter and put together in reverse order. oven now works perfectly

Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

Clean off all broken glass and wipe down the debree,figure what side the glass goes then unscewed the base then the sides then add gorrilla glue on the edges to help set the glass in place had some hold it the screw th center bottom in first then got the sides in place with the bottom rack then screw it all back in to place making sure the side and top were in place right that was it.