ARRS6550E-P1143905NWW Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sherry from Mountain Ranch, CA
- Parts Used:
- R0706010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven door hinge broken
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Westlake, OH
- Parts Used:
- R0706011
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door wouldnt shut evenly.
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anita from SANTA FE, NM
- Parts Used:
- W10290350RW, W10290353RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
I only had one working burner, oven o.k.
New electric stove was out of my price range. I ordered one electric burner and 3 drip bowls. looked at part select instructions and repaired 2 that didn't work. Now next month I'll order one more part to fire up the last burner. Also following their clear instructions and I'll have a full working electric stove for a little over 100.00 dollars, as opposed to a new one at over 900.00.Thank you for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Flavio from Tampa, FL
- Parts Used:
- W10291024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The original parts were in poor shape
Just remove the original parts, unplugged the resistance coils, install the new parts and reconnect the coils.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Blue Mounds, WI
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom baking element was not heating oven to proper temperature
Unscrewed 2 screws holding the bracket on the back of the stove and disconnected the wires from the two clips. Removed back element, connected new elements & replaced screws to back inside wall of oven. Works like brand new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from Wellesley, MA
- Parts Used:
- WPW10259865
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner not working
burner replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanette F from Montezuma, IN
- Parts Used:
- WPW10259868, W10291024, WPW10259865
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners broken, drip bowls needed replaced.
Ordered one day and received the next. Removed old units and replaced with new. Did not miss a home cooked meal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Two Harbors, MN
- Parts Used:
- WP74011243
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bad control switch for stovetop burner
Move stove away from wall to allow working on back of stove. Unplug stove. Remove metal cover from top rear of stove. Pull control knob off of control (front of stove) Remove 2 screws holding infinite control in place (front of stove) Replacement control not identical to original control, having more terminal lugs and different physical arrangement. I used the terminal letters as a guide for placement of wires. The letters were not exactly the same, but close enough. Re-attach control to stove with 2 screws. Re-attach back metal panel to stove. Shaft on replacement control is smaller diameter and different shape from original, so I removed ribs from inside of control knob hole and then squirted a small amount of hot glue into the hole. Smearing a small amount of cooking oil onto shaft of replacent control I then slid the control knob onto the control shaft, holding it in place until the glue cooled and set. Plug stove back in, and return stove to its position next to the wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patty from East Patchogue, NY
- Parts Used:
- W10291024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drip pans were old and corroded
ulplugged elements and dropped in new pans
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Madison, WI
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven heating element burnt out
The repair was simple, two screws and plug in and it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Suffield, CT
- Parts Used:
- WP77001094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no heat from bottom element
1. waited unsuccessfully for heat (one hour) 2. realized the bottom element wasn't working (one minute) 3. found part on-line from pictures (five minutes) 4. ordered part (one minute) 5. received part (36 hours) 6. installed part (five minutes) 7. "THAT'S how you fix the oven" look to husband (1-2 years)
Was this instruction helpful to you?
Thank you for voting!