ACR4503SEB0 Amana Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ralph from TEATICKET, MA
- Parts Used:
- WPW10299224
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Broken spring hinge
the door came apart fairly easy getting it all back together was another story lining up glass and panels that have already been heated was fun but its back together and working fine.... It should be noted that I have a warranty for the stove but the hoops I had to jump thru and the time it would take for the tech to come it was easier to do it myself!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PLUM CITY, WI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven not keeping correct temp and sometimes would not relight when temp went dropped.t
Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from KENT, OH
- Parts Used:
- WPW10299224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven door hinge spring was broken and made the door heavy to open and close
I took the door off the oven frame by releasing the hinge latches and lifting and pulling the door outward to remove it . Then I removed the glass outer cover by taking off the philips screws and then unscrewed the door hinges . I then reversed the order to replace it .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Mifflinburg, PA
- Parts Used:
- WP3196548
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The Range took forever to achieve the proper heating temperature with an inability to maintain a steady heat
I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DEERING, NH
- Parts Used:
- WPW10299224
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Busted door hinge
Wrestled with it for ten minutes and then watched a youtube video on how to set the locks on the oven door hinges in order for the door to be installed. The video was instrumental
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Irving, TX
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from SALEM, OR
- Parts Used:
- WPW10200660, WPW10031790
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced screw
By hand screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilton from CANYON LAKE, TX
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven bake would not heat up at all.
Very simple.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!
NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!
NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from LANCASTER, SC
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element had burned into
The video was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from MILL CITY, OR
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Extremely easy repair
Unplug stove. Remove the two screws attaching the element to the rear of the oven. Carefully pull out. Disconnect wires. Reconnect wires. Screw back in. Done. The hardest part was moving the stove away from the wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from Summerfield, FL
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced old drip pans
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from BRADENTON, FL
- Parts Used:
- WPW10196406, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip pans were not original to range, I could not get them clean.
I reoved old drip pans and installed new ones. Very easy, they look great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Clermont, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not reaching temperature
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from SYLVA, NC
- Parts Used:
- WPW10299224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Compressor would not shut off at the maximum recommended pressure (150psi)
Removed face plate (4 screws). Removed 2 screws holding manifold in place. Detached wires from the switch. No need to mark them - they don't have to go back on any particular terminal. Remove the switch from the manifold with an adjustable wrench. Replace with new switch (thread sealing compound on the new switch is sufficient - no need for teflon tape). Reattach wires and reassemble manifold and face plate. Easy fix!
Was this instruction helpful to you?
Thank you for voting!